INDUSTRIA CHIMICA REGGIANA TECHNICAL SHEET S01 FLASH-1 STUCCO UV One component polyester putty A) DESCRIPTION AND FIELDS OF APPLICATION: It characterizes for an exceptional filling power. Thanks to a very fast drying by means of UV-rays, it avoids the problems of all traditional putties, allowing the sanding immediately after the exposure (it doesn’t cause any overheating of the surface to be treated), with a better adhesion even on difficult surfaces; no pin-holes that might be caused by the mixing with a catalyst; no waste of catalyzed product; easy application even during the hot season; constant drying times; no pot-life. It is allowed to use it traditionally as well (with hardener). B) TECHNICAL DATA: Composition Specific weight Available colours Safety data Unsatured polyester resins and mineral charges 1.75 ± 0,1 Neutral See the safety data sheets * Iron, steel sheet, plastics (polyester reinforced with fiberglass) * Original paints or old well-established finishes * Clean the surface to be treated with Antisil V09 and make sure it is dry and free from silicone, wax, grease and any extraneous material. * On primers or enamels sand and clean the surface before the putty application. D) CAUTIONS: * Store in a cool and dry place. INDUSTRIA CHIMICA REGGIANA - I.C.R. S.p.A 42100 Reggio Emilia - Via M. Gasparini, 7 - Tel. +39 0522 517803 - Fax +39 0522 514384 - e-mail: [email protected] - www.icrsprint.it Uff. Comm.le Italia: 42100 Reggio Emilia - Via Neviani, 5 - Tel. +39 0522 517803 - Fax +39 0522 231819 International Department: 42100 Reggio Emilia - Via Neviani, 5 - Tel. +39 0522 513738 -Fax +39 0522 512446 Stabilimento: 42025 Cavriago - Via Nizzola, 5 - Tel. +39 0522 371818 - Fax +39 0522 575110 Stabilimento: 06074 Perugia - Via Trasimeno Ovest, 159/Z/13 - Tel. +39 075 518611 - Fax +39 075 5186125 CAPITALE SOC. € 557.820,00 – R.E.A. N. 82109 M. R.E. 000534 - Reg. Imprese, COD. FISC. e PART. IVA 00140910357

INDUSTRIA CHIMICA REGGIANA S01 FLASH-1 STUCCO UV sheet # S01 Knife application 2-5' at 20 cm. P60-P120 for the coarse polishing P180-P220 for the finishing UV filling primer Polyester spray putty Isopol primers Acrylic primers Technical indications and advices are based on our own experiences. We assure the perfect quality of products. However, being the utilization out of our control, we assume no responsibility on the results obtained INDUSTRIA CHIMICA REGGIANA - I.C.R. S.p.A Page 2 CAPITALE SOC. € 557.820,00 - R.E.A. N. 82109 M. R.E. 000534 - Reg. Imprese, COD. FISC. e PART. IVA 00140910357...

INDUSTRIA CHIMICA REGGIANA 1-3% paste hardener pot-life 3-7' at 20°C Knife application < 30' at 20 °C 4-5' at 1 m. P60-P120 for the coarse polishing P180-P220 for the finishing F)TOOLS CLEANING: * With nitro or washing thinner. G) RECOATING : UV filling primer Polyester spray putty Isopol primers Acrylic primers Technical indications and advices are based on our own experiences. We assure the perfect quality of products. However, being the utilization out of our control, we assume no responsibility on the results obtained INDUSTRIA CHIMICA REGGIANA - I.C.R. S.p.A Page 3 CAPITALE SOC. € 557.820,00...