I.CH Hybrid Stepper Motor I.CH MOTION CO., LTD MOTION WORLD I.CH Motor supply a complete range of stepper motor. The HXX1 series hybrid stepper motors are optimized for superior Reger to specification of individual models for standard lead torque characteristics. The HXX2 series hybrid stepper wires configureation. Motors can be supplied with 4, 6 or 8 motors feature low rotor inertia for maximum possible Angular ACCURACY acceleration. The HXX5 series provide smooth operation as Standard angular accuracy is ±5%. Angular accuracy is well as the fine positioning capability required for microstep defined as the deviation from a theoretical position, in percentage of one step , asfter any number of steps. Motors may be customized with value added features Holding torque including, but not limited to : gearboxed, encoders, shaft The typical values of holding torque of the different models details, leadwire-connector assemblies, connection box, and are indicated in the data charts. Holding torque is measured with two phased each supplied at the rated current. All specification shown are typical at 20℃ unless otherwise Motors are manufactured according to EN 60034-1: 1995-02. Shaft extensions Motors with drive voltage higher than or equal to 120v are All motors can be supplied with single or double ended shaft suitable to be fitted on machines equipped with additional insulation or when the motor itself has the grounding through The motor rotation can rn clockwise or counterclockwise, Due to thermal consideration, stepper motors can’t always be Operating temperature operated continuously in dynamic condition at their static Ambient operating temperature : -20℃ to +40℃ rated phase current leads upon request; however, rated current and torque many be reduced. www.ICHmo.com Page 1 of 30 STP-

Product Number Code For HB Stepper Motor D Shaft type : S=single, D=double, Blank=both Phase current (A) :0.6 Torque (N.cm) : 303 Connection – Dependent Ratings For 8 Lead Motors Stepper motors supplied with 8 leads provide maximum flexibility and allow the user to decide what connection method is most suitable for the application. Some of the motor phase Characteristics are dependent on the connection method chosen for the windings. The values for current, resistance, and inductance shown in the data tables for 8 lead motors assume a unipolar connection and measure form the center tap to the...

HYBRID STEPPER MOTOR General Specifications Step Angle(Accuracy )------- 1.8°(±5%) Resistance Accuracy -------- ±10% Inductance Accuracy -------- ±20% Temperature Rise ----------- 80℃Max. Ambient Temperature -------- -10℃~50℃ Insulation Resistance ------ 100Mohm Min, 50VDC Dielectric Strength -------- 500VAC for one minute Shaft Radial Play ---------- 0.06Max. (450 g-load) Shaft Axial Play ----------- 0.08Max.(450 g-load) Mechanical Dimensions Standard Leadwire Configuration Complementary Products: Special shaft Encoders Connector Long leadwires

HYBRID STEPPER MOTOR GERNERAL SPECIFICATIONS Step Angle(Accuracy )------- 1.8°(±5%) Resistance Accuracy -------- ±10% Inductance Accuracy -------- ±20% Temperature Rise ----------- 80℃Max. Ambient Temperature -------- -10℃~50℃ Insulation Resistance ------ 100Mohm Min, 50VDC Dielectric Strength -------- 500VAC for one minute Shaft Radial Play ---------- 0.06Max. (450 g-load) Shaft Axial Play ----------- 0.08Max.(450 g-load) Mechanical Dimensions Standard Leadwire Configuration Complementary Products: BRID STEPPER MOTOR MOTOR Special shaft Encoders PhaseYBRID STEPPER Connector Long leadwires

HYBRID STEPPER MOTOR GERNERAL SPECIFICATIONS Step Angle(Accuracy )------- 1.8°(±5%) Resistance Accuracy -------- ±10% Inductance Accuracy -------- ±20% Temperature Rise ----------- 80℃Max. Ambient Temperature -------- -10℃~50℃ Insulation Resistance ------ 100Mohm Min, 50VDC Dielectric Strength -------- 500VAC for one minute Shaft Radial Play ---------- 0.06Max. (450 g-load) Shaft Axial Play ----------- 0.08Max.(450 g-load) Electrical Specification Series Model H364-00403 H364-00905 Mechanical Dimensions Standard Leadwire Configuration Complementary Products: BRID STEPPER MOTOR MOTOR Special shaft...

HYBRID STEPPER MOTOR GERNERAL SPECIFICATIONS Step Angle(Accuracy )------- 1.8°(±5%) Resistance Accuracy -------- ±10% Inductance Accuracy -------- ±20% Temperature Rise ----------- 80℃Max. Ambient Temperature -------- -10℃~50℃ Insulation Resistance ------ 100Mohm Min, 50VDC Dielectric Strength -------- 500VAC for one minute Shaft Radial Play ---------- 0.06Max. (450 g-load) Shaft Axial Play ----------- 0.08Max.(450 g-load) Mechanical Dimensions Standard Leadwire Configuration BI-POLAR(4 LEADS) UNI-POLAR(6 LEADS) Complementary Products: Special shaft Encoders Connector Long leadwires

HYBRID STEPPER MOTOR GERNERAL SPECIFICATIONS Step Angle(Accuracy )------- 0.9°(±5%) Resistance Accuracy -------- ±10% Inductance Accuracy -------- ±20% Temperature Rise ----------- 80℃Max. Ambient Temperature -------- -10℃~50℃ Insulation Resistance ------ 100Mohm Min, 50VDC Dielectric Strength -------- 500VAC for one minute Shaft Radial Play ---------- 0.06Max. (450 g-load) Shaft Axial Play ----------- 0.08Max.(450 g-load) Electrical Specification Series Model H352-00908 H352-00906 H352-00904 H352-00804 H352-01408 H352-01406 H352-01404 H352-01004 Mechanical Dimensions Standard Leadwire Configuration...

HYBRID STEPPER MOTOR GERNERAL SPECIFICATIONS Step Angle(Accuracy )------- 1.8°(±5%) Resistance Accuracy -------- ±10% Inductance Accuracy -------- ±20% Temperature Rise ----------- 80℃Max. Ambient Temperature -------- -10℃~50℃ Insulation Resistance ------ 100Mohm Min, 50VDC Dielectric Strength -------- 500VAC for one minute Shaft Radial Play ---------- 0.06Max. (450 g-load) Shaft Axial Play ----------- 0.08Max.(450 g-load) Mechanical Dimensions Standard Leadwire Configuration BI-POLAR(4 LEADS) Complementary Products: Special shaft Encoders Connector Long leadwires