Aluminum Transfer Pumps Operation, Installation & Parts Manual

Product catalog summary

General Safety Information

Description: This document serves as an installation, operation, repair, and parts manual for Hypro Self-Priming Centrifugal Pumps, specifically models 1572-SPX and 1573-SPX. These pumps are designed for high-capacity liquid transfer tasks, suitable for farm jobs and de-watering applications.

Specifications:

1572-SPX: Max Flow Rate: 145 gpm, Max Pressure: 50 psi, Max Total Head: 115 ft, Max Suction Lift: 28 ft, Ports: 2" NPT Inlet/Outlet, Engine: Honda GX120.
1573-SPX: Max Flow Rate: 280 gpm, Max Pressure: 50 psi, Max Total Head: 115 ft, Max Suction Lift: 28 ft, Ports: 3" NPT Inlet/Outlet, Engine: Honda GX160.

Warnings and Safety Precautions:

Avoid pumping flammable or explosive fluids.
Do not exceed recommended speed, pressure, and temperature (140˚ F).
Secure discharge lines before starting the pump.
Regularly inspect hoses and connections.
Protect the pump from freezing conditions.
Avoid operating gasoline engines in enclosed areas.

Installation and Operation:

Ensure the pump is primed before starting.
Check fuel and oil levels before operation.
Follow specific steps for starting and stopping the pump.

Maintenance:

Flush and drain the pump after use to prevent corrosion.
Inspect and replace worn parts as necessary.
Store the pump in a clean, dry environment.

Troubleshooting: Common issues include no discharge, low discharge, and fluid leaks. Solutions involve checking for air leaks, ensuring proper hose size, and inspecting for blockages.

Performance Data: Performance varies with fluid density and viscosity. Specific flow rates are provided for different pressure levels.

Parts List: Detailed parts lists for models 1572-SPX and 1573-SPX are included, specifying part numbers and descriptions. Parts include O-Rings, Gaskets, Check Valves, Plugs, Bolts, Washers, and a Frame.

Warranty Information: Hypro provides a limited warranty covering defects in material and workmanship under normal use. The warranty period is one year for most products, five years for oil crankcase plunger pumps, and ninety days for accessories. Forged brass pump manifolds are warranted for the life of the pump against defects and environmental damage. The warranty excludes damage from excessive use, incompatible fluids, freight damage, freezing, normal wear and tear, misapplication, negligence, alterations, or repairs affecting performance.

Return Procedures: Products must be flushed of chemicals and labeled before shipping to Hypro for service or warranty consideration. Hypro may request a Material Safety Data Sheet and reserves the right to dispose of products containing unknown substances. For service or warranty assistance, contact Hypro with detailed information about the problem, including model number, purchase details, and specifics about the pump's operation and environment.

Contact Information: For technical assistance, call 1-800-445-8360. For service or warranty assistance, call 1-800-468-3428 or fax (651)766-6618. Products returned for warranty work should be sent prepaid to Hypro's Service Department in New Brighton, Minnesota.

Catalog excerpts

Aluminum Transfer Pumps Operation, Installation & Parts Manual-2

Basket Strainer The basket strainer supplied with this pump is to be used when transferring solutions that may contain debris and solids which could become lodged in the pump or damage the impeller. Because of the high flow capacity of this pump, unknown debris could be siphoned off the bottom of the tank. Install the strainer on the suction side of the pump whenever possible to avoid pump damage. Please Note: It is illegal to ship or transport any hazardous chemicals without United States Environmental Protection Agency Licensing. 1.Always drain and flush pumps before servicing ordisassembling...

Open the catalog to page 2

Aluminum Transfer Pumps Operation, Installation & Parts Manual-3

Note: Pump must not be run dry. Make sure there is water in the priming chamber. > 1.Stop pump for a short time: Run engine throttled all the way down (fully to the right). Turn engine switch to OFF position.2.Stopping pump for storage:Turn fuel cock to OFF position instead of turning the engine switch off. Let the engine idle for 2 to 3 minutes until fuel in carburetor is depleted and engine stops. If a valve is installed on the discharge hose, you may run pump with valve closed during this procedure. > 1.Drain pump. Flush Pump after Use.One of the most common causes for faulty pump performance...

Open the catalog to page 3

Aluminum Transfer Pumps Operation, Installation & Parts Manual-5

Performance Data is based on testing with water.Performance will vary with fluid density and/or viscosity. 0PSI5 PSI10 PSI15 PSI20 PSI25 PSI30 PSI35 PSI40 PSI45 PSI50 PSI >

Open the catalog to page 5

Aluminum Transfer Pumps Operation, Installation & Parts Manual-8

Hypro warrants to the original purchaser of its products (the "Purchaser") that such products will be free from defects in material andworkmanship under normal use for the period of one (1) year for all products except: oil crankcase plunger pumps will be free from defectsinmaterial and workmanship under normal use for the period of five (5) years, and accessories will be free from defects in material andworkmanship under normal use for the period of ninety (90) days. In addition, Hypro warrants to the purchaser all forged brass pumpmanifolds will be free from defects in material and workmanship...

Open the catalog to page 8