![HYDROKOMP - logo](https://img.directindustry.com/images_di/logo-p/L84085.gif)
Catalog excerpts
![024040 - 1](https://img.directindustry.com/pdf/repository_di/84085/024040-376841_1m.jpg)
SWING CLAMP CYLINDERS block housing with overload protection, single-/double-acting, pmax. 500 bar Description: Operating conditions: Swing clamp cylinders release the clamping point on the workpiece. With this, it is easy to change the workpiece. For any risk of exceeding the permitted volume flow a throttle check valve must be interposed into the oil supply line (see data sheet 700-15). This hydraulic swing clamp cylinder operates as double-acting pull cylinder, whereas part of the stroke is used to rotate the piston. The model with 0° swing angle operates only vertical as pull cylinder. To guarantee a long lifetime the cylinders have an integrated metal wiper as standard. For hydraulic oil supply, the cylinders are equipped with threaded port and manifold connection with O-ring for drilled channels. Counter-hold the clamp arm when tightening or loosening the counter nut in order to prevent torque transfer to the piston rod and to avoid damage to the ball guide. Models with 0°, 30°, 45°, 60° and 90° swing angles are available. The permitted operating pressure is depending from the clamp arm length. Models with other swing angles can be supplied as special designs Except from standard clamp arms also special clamp arms can be assembled. The maximum operating pressure of 500 bar does not apply for each clamp arm length. For details about the permitted operating pressure see the diagrams below. You can select between right or left turning models with various standardized swing angles. The safety instructions for swing clamp cylinders in our catalogue or on our website and the current accident prevention regulations must be considered. The integrated overload protection protects the swing mechanism from demage due blockage of the rotation or improper assembly of the clamp arm. Webcode: 024040 We also design and manufacture special designs Connections: G1/4 threaded port Manifold with O-ring Effective clamping force FSp depending from operating pressure p: e Advantages: Protecting metal wiper Integrated overload protection FSp FSp Oil supply through drilled channels or threaded port connection Piston Ø 63 mm Fixture can be easily loaded and unloaded Effective clamping force FSp [kN] Maximum clamp arm length e [mm], only relevant for clamp arms type Easy to assemble with self designed clamp arms Standard and special clamp arms available (see page 2) Various contact bolts available (see data sheet 1000-1) Example A: - cylinder with piston Ø 25 mm - present operating pressure p = 250 bar - clamp arm type 2, length 40 mm resulting clamping force FSp ~ 2,5 kN Example B: - cylinder with piston Ø 40 mm - present operating pressure p = 250 bar - clamp arm type 1, length e = 60 mm resulting clamping force FSp ~ 8,5 kN 240-40 / 02-13 *Subject to change without notice, compare issue no. at www.hydrokomp.de. Hydraulische Komponenten GmbH Siemensstraße 16, 35325 Mücke (Germany) Phone: +49 6401 225999-0 Fax: +49 6401 225999-50 E-mail: info@hydrokomp.de Internet: www.hydrokomp.de
Open the catalog to page 1![024040 - 2](https://img.directindustry.com/pdf/repository_di/84085/024040-376841_2m.jpg)
Swing clamp cylinders with block housing Technical data: plugs inclusive Piston Ø Clamping stroke Swing stroke Total stroke Min. operating pressure Max. volume flow Oil requirement/stroke Oil requirement/reset a b c dØ eØ A/F g h k l m o pØ s t u The threaded ports A and B aswell the two transverse bores omit at the flange design. right turning Clamp arms: Compatible clamp arms: Dimensions for house production of clamp arms: For these swing clamp cylinders, standard clamp arms are available as accessories. All necessary information about this can be found on the data sheet «Swing Clamp...
Open the catalog to page 2