*mydirectindustry

S4VHL

Product catalog summary

Overview
The S4VHL and S4VHLDI are hydraulic submersible sludge/slurry pumps designed for handling wastewater and sewage. They are capable of fitting through a 20-inch diameter manhole and are primarily used for sewer by-pass into force mains and general transfer of solids-laden fluids. The pumps are available in aluminum or ductile iron construction with a shut-off head at 200 feet.

Features

Compact size allows passage through a 20-inch diameter opening.
Oil-lubricated seals enable dry running.
Optional tungsten carbide-coated wear parts.
Fully recessed stainless steel vortex impeller capable of passing 3-inch semi-solids.
Can be bolted directly into a pipeline or used with a suction hose for underwater dredging.
Safe hydraulic drive suitable for hazardous or impractical electric power environments.
Dependable gear-type hydraulic motor.
Operates with HT25 to HT60 power units or other hydraulic power sources with flows of 14-25 GPM.

Specifications

Weight: Aluminum - 165 lbs (75 kg), Ductile Iron - 265 lbs (120 kg).
Dimensions: Height - 33 inches (84 cm), Width - 19 3/4 inches (50 cm).
Discharge: 4-inch NPT(F).
Inlet Flange: 4-inch, 125# ASA.
Solids Handling: Up to 3 inches (8 cm).
Hose Ports: 1-inch (-16) SAE.
Pump Body: Heat-treated aluminum (S4VHL) or ductile iron (S4VHLDI).
Impeller, Wear Ring, and Wear Plate: Stainless Steel.
Shaft: Stainless Steel.
Shaft Seal: Standard Carbon/Ceramic, Optional Silicon Carbide.
Elastomers: Standard Buna N.
Hydraulic Oil: 214-320 s.s.u. @ 100°F (64°C).
Input Flow: Max 25 GPM (95 LPM).
Operating Pressure: Max 3000 PSI (204 Bar).
Power Source: Any open center hydraulic system.

Contact Information
Hydra-Tech Pumps, 167 Stock Street, Nesquehoning, PA 18240. Phone: 570-645-3779, Fax: 570-645-4061, Website: www.hydra-tech.com, Email: [email protected].

Catalog excerpts

4” HYDRAULIC SUBMERSIBLE SLUDGE / SLURRY PUMP MODELS S4VHL (Aluminum Body) S4VHLDI (Ductile Iron The S4VHL is designed to handle wastewater and sewage and will fit through a 20" diameter manhole . Primary uses for this pump are: Sewer by-pass into force mains and general transfer of solids laden fluids. This versatile pump is offered in aluminum or ductile iron construction. Shut off head at 200 feet. FEATURES Small Overall Size allows pump to fit through a 20" diameter opening Oil Lubricated Seals (can run dry) Tungsten Carbide Coated wear parts as an option Fully Recessed SS Vortex Impeller (will pass 3" semi-solids), SS wear rings & wear plate Can be bolted directly into a pipeline or fitted with a suction hose for underwater dredging Safe Hydraulic Drive can be used where electric power is hazardous or impractical Dependable gear type hydraulic motor Operates with our HT25 to HT60 power units or other hydraulic power sources capable of flows of 14 - 25 GPM Stainless Steel model available 167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061 Website: www.hydra-tech.com E-Mail:

Open the catalog to page 1

Liters/Minute CAPACITY Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory. 167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061 Website: www.hydra-tech.com E-Mail: [email protected]

Open the catalog to page 2