Tools 1kV
128Pages

_TECHNICAL SHEETCLAMP DEVICE FOR SCREW CONNECTORS 6.2013 PRODUCER: „HUBIX” cross section Tool is made of stainless steel. One insulation layer, orange, made of plastisol. Tools are controlled and tested (10kV/10s) in accordance with EN 60900:2012. Live working up to 1000V a.c. and 1500V d.c. Tools are used for a better handling of screw connectors on the installation of connecting boxes. Insulated or insulating hand tools should be properly stored to minimize the risk of damage to the insulation due to storage or transportation. These tools should be stored generally separated from other tools to avoid mechanical damage or confusion. Tool should be prevented from excessive heat and sun light. Use a dry tissue to clean. When tool becomes strong soiled use suitable solvent to clean. Before use, each hand tool should be visually inspected by the user. An annual visual examination by a suitably trained person is recommended to determine the suitability of the tool for further service. The visual check shall be considered successful if: o The tool (in particular the insulation) is free from external defect, o The marking is legibly and complete.

Don’t use damaged, worn-out (cracks or deep scratches on insulation) or dirty tools in live working. Tool which becomes wet must be dried before use ATTENTION! In case of doubt after visual examination, the routine dielectric test should be preformed. For check and periodic inspection to be carried out in according to below table.

CHARACTERISTICS Totally made of insulating material, polyamide with the addition of fiberglass. Tool is controlled and tested (10kV/10s) in accordance with EN 60900:2012 Live working up to 1000V a.c. and 1500V d.c. It is used to hold insulated connectors in live working on overhead lines. Insulated or insulating hand tools should be properly stored to minimize the risk of damage to the insulation due to storage or transportation. These tools should be stored generally separated from other tools to avoid mechanical damage or confusion. Tool should be prevented from excessive heat and sun...

TECHNICAL SHEET INSULATED TORQUE WRENCH ½” PRODUCER: „HUBIX" CHARACTERISTICS Insulated tool, made of CrV steel. Isolation made of an elastomer and polyamide with the addition of fiberglass. Black handle made of insulating material. Tool is controlled and tested (10kV/10s) in accordance with EN 60900:2012 Square drive: ½” Capacity: 5Nm to 50Nm. Length: 370mm Weight: 730g APPLICATION Live working up to 1000V a.c. and 1500V d.c. Tool is used to tighten with suitable torque. It’s used with male hex. socket wrenches HNI or HNIL, socket wrenches HN or HNL and extension bars HPN 125 or HPN 250 to...

Before use, each hand tool should be visually inspected by the user. An annual visual examination by a suitably trained person is recommended to determine the suitability of the tool for further service. The visual check shall be considered successful if: o The tool (in particular the insulation) is free from external defect, o The marking is legibly and complete. Don’t use damaged, worn-out (cracks or deep scratches on insulation) or dirty tools in live working. Tool which becomes wet must be dried before use ATTENTION! In case of doubt after visual examination, the routine dielectric test...

TECHNICAL SHEET REVERSIBLE RATCHET SQUARE DRIVE ½” PRODUCER: „HUBIX" CHARACTERISTICS Insulated tool, made of CrV steel. Insulation made of polyamide with the addition of fiberglass. Direction change switch. Tool is controlled and tested (10kV/10s) in accordance with EN 60900:2012. Square drive: ½” Length: 260mm Weight: 490g APPLICATION Live working up to 1000V a.c. and 1500V d.c. Tool is used with male hex. socket wrenches HNI or HNIL, socket wrenches HN or HNL and extension bars HPN 125 or HPN 250 to tighten or loosen screws, nuts and bolts. It’s used on overhead lines and connecting...

Don’t use damaged, worn-out (cracks or deep scratches on insulation) or dirty tools in live working. Tool which becomes wet must be dried before use ATTENTION! In case of doubt after visual examination, the routine dielectric test should be preformed. FREQUENCY TESTS For check and periodic inspection to be carried out in according to table.

*special version CHARACTERISTICS Insert made of CrV steel. Handle is totally made of insulating material, polyamide with the addition of fiberglass. Tool is controlled and tested (10kV/10s) in accordance with EN 60900:2012. Live working up to 1000V a.c. and 1500V d.c. Tool is used to preliminary tighten and loosen screws in clamps on overhead lines Insulated or insulating hand tools should be properly stored to minimize the risk of damage to the insulation due to storage or transportation. These tools should be stored generally separated from other tools to avoid mechanical damage or...

TECHNICAL SHEETCROSS SOCKET WRENCH 5.2013 PRODUCER: „HUBIX” reference CHARACTERISTICS 4-socket end, galvanically separated, made of CrV steel. Handle is made of insulating material, polyamide with the addition of fiberglass. Tool is controlled and tested (10kV/10s) in accordance with EN 60900:2012. Live working up to 1000V a.c. and 1500V d.c. Tool is used to tighten and loosen connection and clamping screws on overhead lines and connecting boxes Insulated or insulating hand tools should be properly stored to minimize the risk of damage to the insulation due to storage or transportation....

Don’t use damaged, worn-out (cracks or deep scratches on insulation) or dirty tools in live working. Tool which becomes wet must be dried before use ATTENTION! In case of doubt after visual examination, the routine dielectric test should be preformed. For check and periodic inspection to be carried out in according to table.

TECHNICAL SHEET TUBULAR SOCKET WRENCH PRODUCER: „HUBIX” reference CHARACTERISTICS Insulated tool, made of CrV steel. Two layers of insulation, white and orange with plastisol. In the top of over a distance 15mm single layer insulation. Tool is controlled and tested (10kV/10s) in accordance with EN 60900:2012. Live working up to 1000V a.c. and 1500V d.c. Tool is used to tighten or loosen screws and nuts of fuse bases. It used with extension bars HPN-125, HPN-250 and drive handles HT or HL Insulated or insulating hand tools should be properly stored to minimize the risk of damage to the...