SNDH-H SERIES Speed Sensors DESCRIPTION The SNDH-H Series Hall-Effect Speed Sensors uses a magnetically biased, Hall-effect integrated circuit to accurately sense movement of ferrous metal targets. The specially designed IC (integrated circuit) and a permanent magnet are sealed in rugged, probetype packages. The flux density of the permanent magnet alters when approached by ferrous metal. This is detected by the Hall ICs. If the sensor is positioned at the circumference of a revolving gear wheel, for example, it detects the teeth and tooth spaces, supplying a digital pulse output with frequency proportional to gear wheel speed. Optimum performance is dependent upon variables which must be considered in combination: target material, geometry and speed, sensor/target gap, and environmental temperature. • Solid state, non-contacting Hall-effect magnetic sensing allows the device the ability to sense through dust, dirt and debris, enhancing reliability and product life • Air gap up to 2,5 mm allows the sensor to be located up to 2,5 mm away from the target • High frequency switching capability (to 15 kHz) allows the device to handle high RPMs (SNDH-H3L-G01) • O-ring seal allows device to be sealed into housings • Two housing materials allow flexibility within the application: stainless steel (corrosion and rust resistant): SNDHH3L-G01; plastic: SNDH-H3C-G04 • Various probe lengths (27,5 mm, and 40 mm) simplify use within the application • High operating temperature of -40°C to 125°C (SNDH-H3C-G04) allows the device to be used in high temperature applications (e.g., engines) • Digital current sinking output (open collector) simplifies electrical interfacing to control systems • Multiple connector options (Bosch 928000453, Delphi-Packard Metripak 150.2 Type 101) simplify installation • Omnidirectional capability eliminates the need to align the sensor to the target, allowing the user to simply bolt the device (SNDH-H3C-G04, SNDHH3L-G01) • Zero speed indicates that the rotation has stopped, allowing the device to work at extremely low RPMs • Stable performance over temperature range and air gap range POTENTIAL TRANSPORTATION APPLICATIONS • Transmission speed sensing in heavy duty trucks, buses,agriculture and construction machines • Wheel speed detection in material handling, agriculture, and construction machines • Motor speed sensing in vehicle powertrain and hybrid engines in heavy duty trucks, buses, agriculture and construction machines Not recommended for Aerospace or Defense applications. PORTFOLIO The SNDH-H Series is part of a portfolio of electronic speed and position sensors that use a variety of technologies to detect speed, direction, or position of a moving ferr

SPEED SENSORS SNDH-H SERIES TABLE 1. SPECIFICATIONS Characteristic Supply voltage range digital current sinking (open collector) Supply current Output current Output leakage current Reverse output voltage alignment required Target orientation Zero speed Operating frequency range Operating temp. range stainless steel Dielectric Housing material Sensing air gap Target tooth width Target slot width Tooth height Target width Sensor misposition to target dependent on target geometry Probe length Probe diameter Delphi-Packard Metripak 150.2 Type 101 Short circuit protected. TABLE 2. ORDER GUIDE Catalog...

SPEED SENSORS SNDH-H SERIES 17,0 2,54 MAX. FIGURE 1. MOUNTING DIMENSIONS (FOR REFERENCE 3 cond.,20 MM.) Cable ONLY: AWG twisted, with extruded PVC jacket Cable 3 cond.,20 AWG twisted, with extruded PVC jacket Conductors: extruded PVC 38,1 Black (common) Green (output) Red (power) Black (common) Green (output) Red (power) Cable: 3-wire, 20 AWG, black PVC jacket 17,8 Connector: Deutsch DT06-3S Cable: 3-wire, 20 AWG, black PVC jacket 17,8 12,67 345,4 SNDH-H Series Datasheet | sps.honeywell.com/ast | 3 3

WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicable warranty period. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgment or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer’s...