Sanitary Turbine Flowmeters Product Bulletin HO-SA-107J Perfecting Measurement TM SANITARY TURBINE FLOWMETER WITH 3-A LABEL FOR PROCESS LIQUID MEASUREMENT The Hoffer Sanitary Design Turbine flowmeter is accepted as meeting 3-A Sanitary Standard No. 28-03 for measurement of process liquids where high sanitary standards are required. Available in 11 sizes, ¼” to 3” with standard Tri-Clamp™ fittings, covering flow rates for 0.35 to 650 GPM. Technical Data Flowmeter Size Linear Flow Range (US GPM) Tri-Clamp™ Size (Inches) Refer to Note 1 Min. Max. Nominal Pulses/ Gallon ’K’ Factor Pulses/ Gallon Nominal Max. Frequency (Hz) Length (Inches) *Model HO3A 1½ X 1/4A .35 3.5 15,000 900 3.56 Model HO3A 3/4 X 1/4A .35 3.5 15,000 900 3.56 *Model HO3A 1½ X 3/8A .75 7.5 8,900 1100 3.56 Model HO3A 3/4 X 3/8A .75 7.5 8,900 1100 3.56 *Model HO3A 1½ X 1/2A 1.25 9.5 5,800 900 3.56 Model HO3A 3/4 X 1/2A 1.25 9.5 5,800 900 3.56 *Model HO3A 1½ X 5/8A 1.75 16 5,200 1400 3.56 Model HO3A 3/4 X 5/8A 1.75 16 5,200 1400 3.56 *Model HO3A 1½ X 3/4A 2.5 29 2,200 1065 3.25 Model HO3A 1½ X 1A 4 60 840 840 3.56 Model HO3A 1½ X 1¼A 6 93 400 620 4.59 Model HO3A 1½ X 1½A 8 130 230 500 4.59 Model HO3A 2 X 2A 15 225 120 450 6.06 *Model HO3A 3 X 2½A 25 400 97 650 10.00 *Model HO3A 4 X 3A 40 650 45 500 10.00 ™ Ladish Tri-Clover Div. (Note 1) Ranges shown are standard ranges; other ranges are available. Contact factory. *(Note 2) These sizes require the use of an installation kit to meet “3A” Standard 28-03 specifications. Other sizes are optional. Note: Turbine meter must be installed with pickup coil pointing down to ensure proper cleanability according to the 3A standard. PERFORMANCE SPECIFICATIONS **Accuracy & Linearity: ±0.5% of reading or better. **Repeatability: ±0.1% of reading or better. Temperature Range: -450°F to +450°F, process fluid with Std. Magnetic pickup coil. Signal Output: 10 MVRMS or greater into a 10K ohm load at minimum flow rate. Materials of Construction: 316/316L Dual Rated Stainless Steel (with exceptions noted below): Rotor: 17.4 PH SS. Retaining Ring: 15.7 MO PH SS. Bearings: Hard Carbon Composite. Surface Finish: All meter surfaces meet 3A standards with 32 micro inch finish. Finer finishes for internally wetted surfaces available as an option. Contact factory for details. **Based on 12 point water calibration at 70°F. INSTALLATION KITS FOR HOFFER SANITARY TURBINE FLOWMETER OPTIONAL ACCESSORIES Signal Conditioners/Converters CAT Series (Refer to CAT Technical Data Sheets). Meter Mounted Totalizer/Rate Indicators Model HIT-2A Totalizer/Rate Indicator (Refer to Technical Data Sheet HIT-2A-XXX). Micro Processor Based Flow Computers Flowstar™ and Nova-Flow Series (Refer Flowstar Series and Nova-Flow Series Technical Data Sheets). To achieve optimum performance of the Sanitary Turbine Flowmeter, a minimum of 10 pipe diameters upstream and 5 pipe diameters downstream of meter size pipe must be used. In addition, certain combinations of nominal meter sizes and triclamp sizes, as indicated on the sizing chart, require the use of adaptor piping to meet the latest “3A” 28-03 specifications. To meet these requirements, Hoffer offers optional sanitary installation kits to provide appropriate straight runs before and after the meter to produce optional results. Certain sizes indicated in these kits to meet the latest 3A standards. Contact factory for additional details.

SANITARY TURBINE FLOWMETER MODEL NUMBERING SYSTEM MODEL HO3A ( A ) X ( B ) - ( C ) - ( D ) - ( E ) - ( F / G) - ( TRI ) A. Tri-Clamp Size B. Flowmeter Size C. Minimum Operating Flow D. Maximum Operating Flow E. Bearing Type (C9) Hard Carbon Composite Sleeve Bearing. M-199 Grade. For use in fluids with a pH of 6 and above. (C1) Hard Carbon Composite Sleeve Bearing. M-100 Grade. Acceptable for use in fluids with a pH less than 6 such as wine, vinegar or fruit juice (acidic). Note: Both bearings are approved by the Food and Drug Administration. F. Pickup Coils (1M) (2M) (1MC3PA) (1MC2PAHT) (1ISM)...