Cartridge Kit for Vane Pump HV and HVQ Series Features • Replacement parts for fixed displacement vane pumps (single and double vane pump HV/HVQ series). • Available in both 12 vanes design for industrial application with quiet operating and 10 vanes design for mobile application with higher pressure and wider range of speed. • With the cartridge independent of the shaft, allowing for easy change of flow capacity and field servicing without removing the pump from its mounting. Handling • When ordering, if left hand rotation, special seal, or a specific position of cartridge (shaft end or cover end) is required, it should be specified by ordering code. and rotor may cause scratches in the soft brass surface.) Make sure that the sharp edge of Vane leads direction of rotation. Re-install the two screws hand tight. Use pump cover to align all sections of the cartridge. Carefully remove the cover and tighten the screws. • To reverse rotation of cartridge, remove the two screws and reverse the location of the inlet support plate and outlet support plate (for cartridge kit with flex side plates, Bronze faces must be installed toward the rotor. DO NOT allow the flex plate to slide across the ring and rotor. Rough edges on the ring • When install the cartridge into the body, carefully move back and forth until the cartridge pins drop into the cover holes and one of the chamfers on the cam ring aligns with the cover inlet port. Ordering Code Cartridge Position Omit - For single pump or shaft end in double pump C - For cover end in double pump (Viewed from shaft end) Omi t - Turn right Ring Size (USgpm) 20HV/HVQ - Turn left Shaft Rotation

Cartridge Kit Position and Rotation Bush Shaft End Cover End Bush Turn Right Single Pump, 20HV/HVQ Bush Turn Right Turn Right Turn Right Double Pump Cartridge Kit Components (HV Series) Cartridge Kit Components (HVQ Series) 2.Outlet Support Plate 3.Seal Pack 5.Cam Ring 6.Vane Kit 8.Inlet Support Plate 10.Screw

Instruction for Cartridge Replacement in Single Pump 1. Remove the four cover screws and lift the outlet cover. Pull out the old Cartridge. Discard the old large square cut seal and large O ring of the cartridge. 3. Install square cut seal into the body. Install small O ring and back-up ring on the cartridge outlet support plate hub. Carefully install the cartridge into the body. Install the cover to the body with large O ring in the groove of the body. Install the cover in position; move back and forth until the cartridge pins drop into the alignment holes located within the cover. Install four...

Cartridge Kit 20HV Installation Dimensions mm (inch) Specifications Delivery at 1200 rpm & 7 bar (100 psi) USgpm Displacement Maximum Maximum Speed Pressure Typical Delivery at max speed & pressure L/min (USgpm) Typical Input Power at max speed & pressure kW (hp) 5.2 (7.0) 11.2 (15.0) 17.0 (22.8) 23.5 (31.5) Cartridge Kit 25HV Installation Dimensions mm (inch) Displacement Maximum Maximum Speed Pressure cm3/r (in3/r) L/min (USgpm) Typical Input Power at max speed & pressure kW (hp) Typical Delivery at max speed & pressure

Cartridge Kit 35HV Installation Dimensions mm (inch) Displacement Maximum Maximum Speed Pressure cm3/r (in3/r) L/min (USgpm) Typical Input Power at max speed & pressure kW (hp) Typical Input Power at max speed & pressure kW (hp) Typical Delivery at max speed & pressure Cartridge Kit 45HV Installation Dimensions mm (inch) Specifications Delivery at 1200 rpm & 7 bar (100 psi) USgpm 42 47 Displacement Maximum Maximum Speed Pressure Typical Delivery at max speed & pressure L/min (USgpm)

Cartridge Kit 20HVQ Installation Dimensions mm (inch) Specifications Delivery at 1200 rpm & 7 bar (100 psi) USgpm Displacement Maximum Maximum Speed Pressure cm3/r (in3/r) Typical Delivery at max speed & pressure L/min (USgpm) Typical Input Power at max speed & pressure kW (hp) Cartridge Kit 25HVQ Installation Dimensions mm (inch) L/min (USgpm) Typical Input Power at max speed & pressure kW (hp) Displacement Maximum Maximum Speed Pressure Typical Delivery at max speed & pressure

Cartridge Kit 35HVQ Installation Dimensions mm (inch) Cartridge Kit 45VQ Installation Dimensions mm (inch) Displacement Maximum Maximum Typical Delivery Typical Input Speed Pressure at max speed & Power at max pressure speed & pressure cm3/r (in3/r) rpm bar (psi) L/min (USgpm) kW (hp) Cartridge Kit 45HVQ Installation Dimensions mm (inch) Displacement Maximum Maximum Speed Pressure cm3/r (in3/r) L/min (USgpm) Typical Input Power at max speed & pressure kW (hp) Typical Delivery at max speed & pressure