video corpo

Radius Mill ASR Four Corners : ASRF type
12Pages

{{requestButtons}}

Catalog excerpts

Radius Mill ASR Four Corners : ASRF type - 1

NEW PRODUCT NEWS No.1206 US6884006B2 Pat. No. Radius Mill Four Corners ASRF Grade for processing high-hardness materials Grade for processing stainless-steel materials General purpose for steel Cutting innovation Introducing new JP / JM / GX coating Break through to the new era with an epoch-making tool which improves processing efficiency Economical 4-corner specification JP4005 JM4060 GX2140

Open the catalog to page 1
Radius Mill ASR Four Corners : ASRF type - 2

WHVU^Cffll fS=§) Grades map (First recommendation) Mild Steels Carbon steel j Carbon steel (200HB or less) Alloy steel j Alloy steel Hardened Steels Hardened Steels Pre-Harden Steels Stainless Steel Cast Iron • Chipping and Welding resistance are improved by using a-Al203with smooth surface. As a result, the stable cutting performance has an effect. •Machining efficiency is improved for high-speed,high-feed-rate rough machining by using the hard-layer with fine columnar structure. • Exhibits superior wear resistance when cutting mild steel, carbon steel, alloy steel and tool steel use with...

Open the catalog to page 2
Radius Mill ASR Four Corners : ASRF type - 3

Radius Mill Four Corners ASRF • Uses JP coating optimized for processing high-hardness materials, with higher layer hardness and improved oxidation resistance. • Cemented carbide material use the micro-grained carbide which is most suitable for high hardness material cutting, and the material improves wear resistance and chipping resistance. • Hardened steels (50-60HRC) : SKD11, SKD61, SKH, and SUS420 type etc. Cutting evaluation results SKDl 1 (6OHRC)C0WH!|K|8jigS Wear graph after cutting SKD11 (60HRC) SUS420S (50HRC)CDt3HKSt1SS Wear graph after cutting SUS420 type (50 HRC) Cutting...

Open the catalog to page 3
Radius Mill ASR Four Corners : ASRF type - 4

Numeric figure in a circle O and Alphabetical character comes in a square: ] A^M^C— USA?) Type A (Standard type) B^f y(7y$— toHTJ) Type B (Undercuttype) (.XT—T^ft With air hole) (.XT—T^ft With air hole) Item Code Overall length Shank diameter BeloiJ neck Shank length Extra Long •ED : SBPSKffiTfo • : Stocked Items. Numeric figure in a circle C inch size Item Code •ED : SBPSKffiTfo • : Stocked Items. Standard shape With breaker • : Stocked Items. * : Stocked Items of New products. '■ On late March, 2012 scheduled.

Open the catalog to page 4
Radius Mill ASR Four Corners : ASRF type - 5

Radius Mill Four Corners ASRF •ED : SfSSSTt. • : Stocked Items. «SEP : gatlSTt. No mark : Manufactured upon request only. [Note] The arbor screw for attaching the cutter is included with the arbor, but is not included with the cutter themselves. Parts for optional arbor screws Arbor screw Cutter body Cutter body Cutter body [Note] When supplying air and cutting agent to each flute, please use the arbor screws listed above. They are not included with the cutters themselves. Even with the screws included with the arbor, the arbor can be used as it is for center through.

Open the catalog to page 5
Radius Mill ASR Four Corners : ASRF type - 6

4-corner ASRF type with diameters of 032 to 0100mm have been added to the regular product lineup, offering deep cutting capability as well as specifications greatly surpassing those of 2-corner ASR type inserts. Ay^i 0Dc (mm) Cutter diameter 4-corner specifications with a main cutting blade shape almost identical to that of conventional ASR main cutting blades. ^ With ASRF : Even for deep cutting, stable, high-performance machining with an almost constant load is possible.

Open the catalog to page 6
Radius Mill ASR Four Corners : ASRF type - 7

Radius Mill Four Corners ASRF Select from two types of inserts available as standard products. Low-resistance breaker type Method for defining conditions of insert tip programmatically For roughing processing, please create a program with corner R values close to those shown as references below. next process When corner R is set larger: next process Normally, you should create a program with an input corner R of approximately 4.5. At an approximate input corner R of 4.5, there is no overcutting. surface J\-Yj ~3L\JZC(J/]|_|_L_[H] Processing surface in program Although overcutting occurs...

Open the catalog to page 7
Radius Mill ASR Four Corners : ASRF type - 8

I ^"YL/^hlCjq^Dj^^JPIfeRltB Processing by direct milling is also possible. Since the cutting flute do not extend to the center, there are limitations on the ramp angle and hole diameter, but as shown below, processing by direct milling without a pilot hole is possible for ramping and helical milling. Helical hole mtmm Ramping 'VJ^JUSJU Helical milling [Note] 1. The ramp angle 8 should be set within the ranges listed above. Use at ramp angles of 1° or less is recommended. 2.For hole diameters outside the ranges listed above, a pilot hole should be drilled before milling. illl^ln^) Field Data...

Open the catalog to page 8
Radius Mill ASR Four Corners : ASRF type - 9

Radius Mill Four Corners ASRF WH*IJ$ Cutting region tJ]]Z±fc$m ae Cutting width (mm) ^i^^ltlg ae Cutting width (mm)

Open the catalog to page 9
Radius Mill ASR Four Corners : ASRF type - 10

W^^RWl^ki^ Recommended cutting conditions specialized in High hardened steel is not suitable for Non-heat-treated steel material.

Open the catalog to page 10
Radius Mill ASR Four Corners : ASRF type - 11

Radius Mill Four Corners ASRF 1. These conditions are for general guidance; in actual machining conditions adjust the parameters according to your actual machine and work-piece conditions. (If the over hung is 3Dc or less, the recommended cutting speed is Vc=180~200m/min; 3Dc or more 2. The thick and heavy chips are generated by using this tool. Be sure to remove them with air blow in order to avoid any breakage by blocking with chips. The recommended method is "Spindle center through" when blowing air. (Pay attention when removing chips in cavity work with the machining center <vertical...

Open the catalog to page 11
Radius Mill ASR Four Corners : ASRF type - 12

x.1$(D~r—^ISiitKISS©—flW. 8; Drawings, data in tables, etc. are examples of test results. 1. Cautions regarding handling (1) When removing the tool from the case (package), be careful not to drop it on your foot or drop it onto the tips of your bare fingers. (2) When actually setting the inserts, be careful not to touch the cutting flute directly with your bare hands. 2. Cautions regarding mounting (1) When preparing for use, be sure that the inserts are firmly mounted in place and that they are firmly mounted on the arbor, etc. (2) If abnormal chattering occurs during use, stop the machine...

Open the catalog to page 12

All MOLDINO Tool Engineering Europe GmbH catalogs and technical brochures

  1. EPBTS

    12 Pages

  2. EMXR

    16 Pages

  3. EMXA

    12 Pages

  4. EPDRF-TH

    12 Pages

  5. EPDBPE-ATH

    20 Pages

  6. SCE-R

    6 Pages

  7. RV type

    12 Pages

  8. ABPFN type

    6 Pages

  9. TD4N type

    8 Pages

  10. EHHB-ATH

    8 Pages

  11. EPCDS

    4 Pages

  12. GALLEA series

    24 Pages

  13. WHMB-TH

    12 Pages

  14. EPDRE-ATH

    24 Pages

  15. CBN-EHB

    12 Pages

  16. EHHBE-TH3

    8 Pages

  17. TD6N type

    12 Pages

  18. EB4HR-ATH

    12 Pages

  19. EHX

    12 Pages

  20. EPHB-PN

    8 Pages

  21. EHHRE-TH3

    8 Pages

  22. EDT

    16 Pages

  23. EHSE-TH

    8 Pages

  24. NSB

    12 Pages

  25. WHNSB-TH

    20 Pages

  26. EMSBS

    8 Pages

  27. GS4TN type

    4 Pages

  28. ABP4F

    8 Pages

  29. EPDBEH-TH3

    20 Pages

  30. JM4060

    4 Pages

  31. GX2140

    4 Pages

Archived catalogs

  1. CBN End Mills

    20 Pages

  2. Cutters

    10 Pages

  3. Reamers

    16 Pages

  4. HSS End Mills

    98 Pages

  5. Indexable Tools

    160 Pages