video corpo

Radius Mill : AHR (Heavy Radius Mill) type
12Pages

{{requestButtons}}

Catalog excerpts

Radius Mill : AHR (Heavy Radius Mill) type - 1

Patent Pending Radius Mill: AHR type (Heavy Radius Mill) Cutting innovation The optimum tool for casting work using non-uniform stock material. Hitachi Tool Engineering, Ltd.

Open the catalog to page 1
Radius Mill : AHR (Heavy Radius Mill) type - 2

WSU^ff Cutting Conditions Cutting time(min) Work Material Cutting Speed Cutting depth Cutting Lubricant Single-tip cutting Photograph of flute wear after 20 minutes S^JRnn Conventional

Open the catalog to page 2
Radius Mill : AHR (Heavy Radius Mill) type - 3

Radius Mill: AHR type (Heavy Radius Mill Cutting time(min) WEPJ^ff Cutting Conditions Cutting Speed Cutting depth Cutting LuOricant Single-tip cutting Flute damage condition after 10 minutes SGJKPP Conventional

Open the catalog to page 3
Radius Mill : AHR (Heavy Radius Mill) type - 4

S/VyZ^'CJ Shank Type Straight Shank type Stocked Items. No Mark : Manufactured upon request only.

Open the catalog to page 4
Radius Mill : AHR (Heavy Radius Mill) type - 5

Radius Mill: AHR type (Heavy Radius Mill J^y^^y Bore Type iRTJiZ Bore type No Mark : Manufactured upon request only.

Open the catalog to page 5
Radius Mill : AHR (Heavy Radius Mill) type - 6

f^EKV+t-h Inserts Fig-l WMftZ'Ht Standard shape Carbon steels Hardened steels General cutting, First recommended General cutting, Second recommended Item Code metric JP-Coated JM-Coated JS-Coated ^ : Stocked Items of New products. 0 : Stocked Items. No Mark : Manufactured upon request only.

Open the catalog to page 6
Radius Mill : AHR (Heavy Radius Mill) type - 7

Radius Mill: AHR type (Heavy Radius Mill Item Code Applicable holders [Note] Please use 14mm hexagon wrench. ft\794JM7—JK Bore type Arbor ED : 4P>ffl*ffiT"S"„ • : Stocked Items. &SED : gatlSTt. No Mark : Manufactured upon request only. [ft*] ©7'-A*fflfeUtt,7'-A*C#SUTay*-rA^*>y$*ft;Ctt#SUTay*-ti^ [Note]Arbor screw is attached on an arbor.

Open the catalog to page 7
Radius Mill : AHR (Heavy Radius Mill) type - 8

H ^SMSU'JEii! Features and Applications Announcing the development of a radius mill with a long cutting flute to enable machining even of non-uniform work material formed by casting without worrying about the cutting amount. Even if the cutting amount of the work material is not uniform, rough machining of shaped area by contour machining can be performed. Can also be used for rough machining of flat surfaces of structural areas. Compared to ball end mills of conventional machining methods, this new radius mill offers great leaps in efficiency. Conventional machining method Heavy radius...

Open the catalog to page 8
Radius Mill : AHR (Heavy Radius Mill) type - 9

Radius Mill: AHR type (Heavy Radius Mill Feature comparison by insert shape [Note] 1. The ramp angle 8should be set within the ranges listed above. Use at ramp angles of 0.5° or less is recommended. 2. For hole diameters outside the ranges listed above, a pilot hole should be drilled before milling. tiDHOiMI Cutting range •Y^+t-h mseri : ZDNW1 5051 OOTR Work:FCD450,Dry ®ffl Machine ■ U ^t- M/C15kw Vertical machine:! 5kW tDjAJWllg ae Cutting width (mm) •Y^+t-h mseri : ZDNW1 5051 OOTR Work:FCD450,Dry ffif Machine: MMWC15kw Vertical machine:15kW IjDj&SMpH ae Cutting width (mm)

Open the catalog to page 9
Radius Mill : AHR (Heavy Radius Mill) type - 10

■ H3I(£i§£> Field Data +#3f9M$IJ Reference examples Chip discharge rate Chip discharge rate

Open the catalog to page 10
Radius Mill : AHR (Heavy Radius Mill) type - 11

Radius Mill: AHR type (Heavy Radius Mill S) i)DI]MUfc3SSiti©^T'"S"o Note: Comments from actual users.

Open the catalog to page 11
Radius Mill : AHR (Heavy Radius Mill) type - 12

x.1$(D~r—^ISiitKISS©—flW. 8; Drawings, data in tables, etc. are examples of test results. 1. Cautions regarding handling (1) When removing the tool from the case (package), be careful not to drop it on your foot or drop it onto the tips of your bare fingers. (2) When actually setting the inserts, be careful not to touch the cutting flute directly with your bare hands. 2. Cautions regarding mounting (1) When preparing for use, be sure that the inserts are firmly mounted in place and that they are firmly mounted on the arbor, etc. (2) If abnormal chattering occurs during use, stop the machine...

Open the catalog to page 12

All MOLDINO Tool Engineering Europe GmbH catalogs and technical brochures

  1. EPBTS

    12 Pages

  2. EMXR

    16 Pages

  3. EMXA

    12 Pages

  4. EPDRF-TH

    12 Pages

  5. EPDBPE-ATH

    20 Pages

  6. SCE-R

    6 Pages

  7. RV type

    12 Pages

  8. ABPFN type

    6 Pages

  9. TD4N type

    8 Pages

  10. EHHB-ATH

    8 Pages

  11. EPCDS

    4 Pages

  12. GALLEA series

    24 Pages

  13. WHMB-TH

    12 Pages

  14. EPDRE-ATH

    24 Pages

  15. CBN-EHB

    12 Pages

  16. EHHBE-TH3

    8 Pages

  17. TD6N type

    12 Pages

  18. EB4HR-ATH

    12 Pages

  19. EHX

    12 Pages

  20. EPHB-PN

    8 Pages

  21. EHHRE-TH3

    8 Pages

  22. EDT

    16 Pages

  23. EHSE-TH

    8 Pages

  24. NSB

    12 Pages

  25. WHNSB-TH

    20 Pages

  26. EMSBS

    8 Pages

  27. GS4TN type

    4 Pages

  28. ABP4F

    8 Pages

  29. EPDBEH-TH3

    20 Pages

  30. JM4060

    4 Pages

  31. GX2140

    4 Pages

Archived catalogs

  1. CBN End Mills

    20 Pages

  2. Cutters

    10 Pages

  3. Reamers

    16 Pages

  4. HSS End Mills

    98 Pages

  5. Indexable Tools

    160 Pages