Catalogs >
MOLDINO Tool Engineering Europe GmbH >
High-Feed Ultra End Mill : AHU type

High-Feed Ultra End Mill : AHU type
12Pages

Catalog excerpts

High-Feed Ultra End Mill AHU Grade for processing stainless-steel materials For FWTFWFFand FA type inserts Wall surface accuracy during shoulder milling has been improved. Exceptionally tough High-Feed Ultra End Mill.

Open the catalog to page 1

Grade for processing stainless-steel materials Newly developed PVD technology provides improved layer adhesion and reduced layer peeling due to welding. Coating is optimized for stainless steel processing with reduced coating layer damage. High-toughness substrate is used to improve chipping resistance of cutting edge. KpPn'<S^|IjiL'3N"3"o ' Provides high-performance processing and long tool life in all areas of stainless-steel material processing. Electron micrograph I Level of film remaining Cutting time(min) WMilS W Cutting Conditions Cutting Speed Speed perflute Cutting depth Cutting...

Open the catalog to page 2

High-Feed Ultra End Mill AHU AHU has the outstanding sharpness and toughness. Evolved into the multi-function tool in which a ramping operation is Enlarging the range of applications. Especially, AHU is suitable for turbine-blade machining. It is lineup about two series by cutting edge length. Multi-flute type for low depth of cut. High rigidity type for high depth Cutting force is reduced by high rake geometry. Ramping operation is possible. DIA exaggerated size article is standardized. 30% increasing rigidity compared with comventional by using special steel and chip pocket geometory....

Open the catalog to page 3

Shank type dimensions O (iiil1?1^ADlT<f 0 Numeric figure in a circle C

Open the catalog to page 4

High-Feed Ultra End Mill AHU Bore type dimensions O ttiil1?1^AD^If <> Numeric figure in a circle C Item Code ED : lifi*o°Tt. • : Stocked Items. ^i/D.-?—• \J1£ Modular Mill Head dimensions Numeric figure in a circleC Item Code •ED : SittSSTt. • : Stocked Items. =Ei/*a5-5JI/Sa»ffli/-vV^7, WBT'-A© TIMSHJ r^S^-^S/BBJ C#y-3.fc#DM»ffltt£fcUi:0T<fc*<¥0„ [Note] When»1 and»2 (p.7) are used together as a set, there is no interference. Do not apply lubricants such as grease, etc. to the "contact faces" and "modular screws" of the "modular mill", "special shanks" and "special arbor".

Open the catalog to page 5

(SEKVtJ-h Inserts [Note] when using the insert with Radius bigger than Te2.0, it is necessary to carry out additional processing of cutter body corner part. PJI/SZOAosI Aluminum Alloy ^^^oilk Titanium Alloy General cutting, First recommended General cutting, Second recommended Item Code JP-Coated JM-Coated JS-Coated HD-Coated Carbide ~k '■ Stocked Items of New products. 0 : Stocked Items. No Mark: Manufactured upon request only. — : Not Manufactured.

Open the catalog to page 6

High-Feed Ultra End Mill AHU Special Shanks for Modular Mills Carbide Shank B'P^y BType Item Code Cutter body ED : flBittKSTt" o • : Stocked Items. ©WhenSi;2 ancMI (pp. 5) are used together as a set, there is no interference. ©Commercial milling chucks or shrink-fit holders can be used. ©Dimensions in parentheses are when ABPFM, ARPFM or BCFM is attached. ©For the 040 size, it is recommended that the protrusion length be 200mm or less. W^lfO Steel Shank BS'^y BType Item Code For neck section or total length, additional machining to user specifications is possible. • ED : d¥ffl*£>T?„ • :...

Open the catalog to page 7

I ^Z/D.Z7—SJUfflV7—A' Modular Mill Arbor • ED : (titOST? „ • : Stocked Items. MED : SiiSS STf. No Mark : Manufactured upon request only. [Note]©Coolant Pipe is attached.©The L3 and Lf dimensions in parentheses show the data with ABPFM.ARPFM, or BCFM attached. Arbor (BT,HSK) Features Maximum efficiency for BT,HSK spindle machines due to the reduction in the "actual" overhang in long and extra-long applications. Example : Overhang and Application Area Commercial milling chuck (BT30 type) For neck section, additional machining to user specifications is possible. For neck section, additional...

Open the catalog to page 8

High-Feed Ultra End Mill AHU Recommended cutting conditions [Note] (TTThe ramp angle 8 should be set within the ranges listed above. Use at ramp angles of 1° or less is recommended. ©For hole diameters outside the ranges listed above, a pilot hole should be drilled before milling.

Open the catalog to page 9

High-Feed Ultra End Mill : AHU type - 10

Cutting conditions for cutting aluminum alloy and copper using SD5010 <H^!JD> Shoulder cutting de=0.5DC [Not©] ©Use the appropriate coolant for the work material and machining shape. ©These conditions are for general guidance; in actual machining conditions adjust the parameters according to your actual machine and work-piece conditions. ©Since there is a danger of breakage when using this tool, be sure to use the cutting area cover, protective goggles, safety shoes, etc.

Open the catalog to page 10

High-Feed Ultra End Mill : AHU type - 11

High-Feed Ultra End Mill AHU Overhang and Application Area Cutting Speed Works Machine W&StHm ae Cutting Width(mm) Wj&<fr$k ae Cutting Width(mm)

Open the catalog to page 11

High-Feed Ultra End Mill : AHU type - 12

Field data Note: Comments from actual users. <■ Drawings, data in tables, etc. are examples of test results. 1. Cautions regarding handling (1) When removing the tool from the case (package), be careful not to drop it on your foot or drop it onto the tips of your bare fingers. (2) When actually setting the inserts, be careful not to touch the cutting flute directly with your bans hands. 2. Cautions regarding mounting (1) When preparing for use, be sure that the inserts are firmly mounted in place and that they are firmly mounted on the arbor, etc. (2) If abnormal chattering occurs during...

Open the catalog to page 12