video corpo

EMSBS
8Pages

{{requestButtons}}

Catalog excerpts

EMSBS - 1

Drill for machining ultra-deep minute holes Epoch Micro Step Borer S

Open the catalog to page 1
EMSBS - 2

Enables ultra-deep drilling of minute holes Features of EMSBS New chip-removal stopper technology + high-rigidity neck shape enables high-accuracy drilling of minute holes. Thinning flute shape achieves even higher machining accuracy (Thinning: Drill diameter > φ0.1) Combined with a special starter, it enables stable deep drilling of minute holes. Two types of coating to match various applications For product sizes other than standard product sizes, refer to made-to-order products (up to 100D possible). SD Non ferrous Carbon metal steel Stainless steel Pre-hardened steel New chip-removal...

Open the catalog to page 2
EMSBS - 3

Epoch Micro Step Borer S for Non-ferrous SD Coated Tolerance on shank : h4 Tolerance on dia.: —0.005mm EMSBS0000-00.0-(TH/SD) Indicate the desired coating type by adding "-SD" for SD coating or "-TH" for TH coating at the end of the item code. : Stocked Items. □ : Stocked by specified distributor. Contact with our sales department. Under-neck length (£2) conforms to through-hole drilling depth. Item code

Open the catalog to page 3
EMSBS - 4

Epoch Micro Step Borer S Item Code • This standard cutting condition table is intended as reference cutting conditions. The conditions should be adjusted as necessary according to the actual conditions of machined shape, purpose, machine used, etc. • In general, water-soluble or oil-based coolant should be used to ensure chip removal. • Always use with a G83 program (Peck drilling cycle). • Under-neck length (R2) conforms to through-hole drilling depth. • When drilling through holes, drill the through hole to a depth of between 20% and 30% of the diameter from the tip of the tool. Ex.: For...

Open the catalog to page 4
EMSBS - 5

Epoch Micro Starter O Recommended cutting conditions Epoch Micro Starter Item Code • These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. • In general, water-soluble or oil-based coolant should be used to ensure chip removal. • Always use with a G83 program (Peck drilling cycle). • Hole depth: Be sure to drill to a depth of 60% of

Open the catalog to page 5
EMSBS - 6

We can deliver the size to match customer needs. Manufactured upon request only. Manufactured upon request onlyEMSBS i R Tolerance on shank : h4 Tolerance on dia.: —0.oo5mm designation of under neck length; (B) Designation of coating O Ordering method The under neck length and coating can be freely selected according to the application. Selecting under neck length Selecting coating Please specify the under neck length using (hole depth + tool diameter) as criteria. In general, SD should be selected for non-ferrous materials, and TH should be selected for other materials. [Example 1] For...

Open the catalog to page 6
EMSBS - 7

Stable drilling to 50 holes. Chipping at ho|e #32 Interrupted cutting possible! Number of holes drilled EMSBS Conventional A Conventional B Conventional C . . _ Enables stable machining of powder metallurgy HSS which often causes seizing with other tools. O How to use Epoch Micro Step Borer • Caution points when machining <About pilot holes> Use of the special starter is recommended. * Particularly when drilling high-accuracy holes, please use the special starter. Always perform step drilling using a G83 program. Hole depth: Be sure to drill to a depth of 60% of the diameter. (Ex.: For...

Open the catalog to page 7
EMSBS - 8

The diagrams and table data are examples of test results, and are not guaranteed values. "Epoch" , “ ” and “ ” are registered trademarks of Mitsubishi Hitachi Tool Engineering, Ltd. in Japan. Attentions on Safety 1. Cautions regarding handling (1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is dropped. Be particularly careful regarding contact with the tool flutes. (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with your bare hands. 2. Cautions regarding mounting (1) Before use, check...

Open the catalog to page 8

All MOLDINO Tool Engineering Europe GmbH catalogs and technical brochures

  1. EPBTS

    12 Pages

  2. EMXR

    16 Pages

  3. EMXA

    12 Pages

  4. EPDRF-TH

    12 Pages

  5. EPDBPE-ATH

    20 Pages

  6. SCE-R

    6 Pages

  7. RV type

    12 Pages

  8. ABPFN type

    6 Pages

  9. TD4N type

    8 Pages

  10. EHHB-ATH

    8 Pages

  11. EPCDS

    4 Pages

  12. GALLEA series

    24 Pages

  13. WHMB-TH

    12 Pages

  14. EPDRE-ATH

    24 Pages

  15. CBN-EHB

    12 Pages

  16. EHHBE-TH3

    8 Pages

  17. TD6N type

    12 Pages

  18. EB4HR-ATH

    12 Pages

  19. EHX

    12 Pages

  20. EPHB-PN

    8 Pages

  21. EHHRE-TH3

    8 Pages

  22. EDT

    16 Pages

  23. EHSE-TH

    8 Pages

  24. NSB

    12 Pages

  25. WHNSB-TH

    20 Pages

  26. GS4TN type

    4 Pages

  27. ABP4F

    8 Pages

  28. EPDBEH-TH3

    20 Pages

  29. JM4060

    4 Pages

  30. GX2140

    4 Pages

Archived catalogs

  1. CBN End Mills

    20 Pages

  2. Cutters

    10 Pages

  3. Reamers

    16 Pages

  4. HSS End Mills

    98 Pages

  5. Indexable Tools

    160 Pages