video corpo

EHX
12Pages

{{requestButtons}}

Catalog excerpts

EHX - 1

Exchangeable head End Mill for Die & mold making

Open the catalog to page 1
EHX - 2

Exchangeable Head End Mills for Die & mold making EHX End M ill s e r ie s “Carbide” +“Carbide” = “High accuracy & High rigidity” Double Face Contact Type Special Steel Screw Joint Mono-block Carbide Holder Available with Internal Coolant Double Face Contact Type (Taper + End Face) The EHX series is a revolutionary end mill system that enables Comparison of tool rigidity efficiency, high accuracy and rigidity by combining the advantages The double face contact of the carbide head and of both solid carbide and indexable end mills. carbide holder gives an increase in rigidity of 30%. Security...

Open the catalog to page 2
EHX - 3

First shot Deploy three favorable solid end mills to the EHX series Item code Head type Roughing process of mold can be done withhigh efficiency. Epoch Turbo Mill High-speed cutting for high hardness materialsis possible Cover a wide range application from roughing to finishing. Epoch Power Mill Tool life is comparable to the soild end mill. Work material:STAVAXⒽ(52HRC) Tool dia.: φ12  Machine:HSK-A63  Cutting length:L=50m n=5300min-1 (vc=200m/min) vf =2800mm/min (fz=0.088mm/t) ap×ae=6mm×0.2mm Dry(Air Blow) Down Cut Conventional exchangeable head (L=10m) Advanced TH coating dedicated to the...

Open the catalog to page 3
EHX - 4

Roughing process of mold can be done with high efficiency. Head type : Epoch Turbo Mill : Stocked Items

Open the catalog to page 4
EHX - 5

Cover a wide range application from roughing to finishing. Head type : Epoch Power Mill Curved edge Curved edge Carbide ATH-Coated Helix angle Size (mm) Item code Corner radius Flute length Overall length L r R Re-grinding compatibility range table Item Code Product Name Re-grinding compatibility range (mm) Exchangeable head end mill EHX-ETM Exchangeable head end mill EHX-H-ETM

Open the catalog to page 5
EHX - 6

Straight type Pencil neck type

Open the catalog to page 6
EHX - 7

O How to Install the Head Using a clean cloth, wipe away oil and dust from the taper and end surfaces of the head and holder. Be careful to avoid the possibility of cutting hands when fastening with bare hands directly near the blade tip. Securely fasten the head and holder end surfaces using the enclosed spanner to close off any remaining gap. Refer to the table at right regarding angles for recommended torque when necessary. For stricter usage, refer to the table right for torque wrench fastening. Suitable head (Note) Use the enclosed spanner only. (Typical spanners differ in thickness.)...

Open the catalog to page 7
EHX - 8

When using a holder with a long overhang length, please use the correction factor of the above table in consideration

Open the catalog to page 8
EHX - 9

When using a holder with a long overhang length, please use the correction factor of the above table in consideration.

Open the catalog to page 9
EHX - 10

When using a holder with a long overhang length, please use the correction factor of the above table in consideration. © Use the appropriate coolant for the work material and machining shape. © Use a highly rigid and accurate machine as possible. © These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. © If the rpm available is lower than that recommended please reduce the feed rate to the same ratio.

Open the catalog to page 10
EHX - 11

Work material :DAC0(45HRC) Size :150x150x100mm(Cutting depth 86mm)Machine :HSK-A63Tool Process EHX12-ETM4120-20-TH After 54 minutes processing Processo

Open the catalog to page 11
EHX - 12

The diagrams and table data are examples of test results, and are not guaranteed values. "Epoch" and “ ” are registered trademarks of Mitsubishi Hitachi Tool Engineering, Ltd. in Japan. Attentions on Safety 1. Cautions regarding handling (1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is dropped. Be particularly careful regarding contact with the tool flutes. (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with your bare hands. 2. Cautions regarding mounting (1) Before use, check the...

Open the catalog to page 12

All MOLDINO Tool Engineering Europe GmbH catalogs and technical brochures

  1. EPBTS

    12 Pages

  2. EMXR

    16 Pages

  3. EMXA

    12 Pages

  4. EPDRF-TH

    12 Pages

  5. EPDBPE-ATH

    20 Pages

  6. SCE-R

    6 Pages

  7. RV type

    12 Pages

  8. ABPFN type

    6 Pages

  9. TD4N type

    8 Pages

  10. EHHB-ATH

    8 Pages

  11. EPCDS

    4 Pages

  12. GALLEA series

    24 Pages

  13. WHMB-TH

    12 Pages

  14. EPDRE-ATH

    24 Pages

  15. CBN-EHB

    12 Pages

  16. EHHBE-TH3

    8 Pages

  17. TD6N type

    12 Pages

  18. EB4HR-ATH

    12 Pages

  19. EPHB-PN

    8 Pages

  20. EHHRE-TH3

    8 Pages

  21. EDT

    16 Pages

  22. EHSE-TH

    8 Pages

  23. NSB

    12 Pages

  24. WHNSB-TH

    20 Pages

  25. EMSBS

    8 Pages

  26. GS4TN type

    4 Pages

  27. ABP4F

    8 Pages

  28. EPDBEH-TH3

    20 Pages

  29. JM4060

    4 Pages

  30. GX2140

    4 Pages

Archived catalogs

  1. CBN End Mills

    20 Pages

  2. Cutters

    10 Pages

  3. Reamers

    16 Pages

  4. HSS End Mills

    98 Pages

  5. Indexable Tools

    160 Pages