Catalogs >
MOLDINO Tool Engineering Europe GmbH >
Carbide Thread Mill series

Carbide Thread Mill series
16Pages

Catalog excerpts

ET-PN/EDT-TH EDT-(N)PT- Carbide Thread Mill series

Features Applications Applicable range Cast iron Carbon steel Alloy steep Tool steel Pre-hardened Hardened steel steel 45~55HRC ET-PN EDT-TH, EDT-(N)PT-ATH Parts processing Mold making Features of Epoch Thread Mill ・Tough and strong edge design provides threading of hardened steels. ・Tip shape that reduces cutting resistance suppresses tool bending. ・Drastically reduces tool breakage, Reduces risk a particular problem of breaking New coating with excellent adhesion and wear resustance ecnatsuser raew dna noisehda tnellecxe htiw gnitaoc weN Adhesion of PN coating Conventional coating...

Open the catalog to page 2

Te c h n o l o g y Reduces the risk of breaking off inside By using a tool with a diameter smaller than the inside diameter of the thread, cutting chips are smaller and chip evacuation is improved. The risk of the tool breaking off inside the hole is reduced as a result. One tool - various types of thread milling Right hand, left-hand and fine thread milling can be performed by just changing the NC program. The nominal diameters of the coarse threads and fine threads that can be processed with the same tool are different. (Example: For ET-1.25-16-PN, coarse thread is M8 × P1.25 and fine...

Open the catalog to page 3

: Stocked Items. □: Stocked by specified distributor. Contact with our sales department. ^For information ab

Open the catalog to page 4

©Epoch Thread Mill is an only for threading the inside of holes. ©The above cutting conditions are for the nominal diameters stated in the table. Cutting conditions for other nominal diameters should be calculated taking into consideration the cautions on use (p.15). ©The machinery should be a machining center equipped with NC (numerical control) equipment having a helical interpolation function. ©The feed rate stated in the above conditions table is the feed rate at the tool center during threading. In addition, the per-tooth feed rate is the numerical value at the cutting point. ©Since...

Open the catalog to page 5

4 flutes 1 incomplete thread and 2 complete threads : Stocked Items. □: Stocked by specified distributor. Contact with our sales department. ^For information about tool diameter correc

Open the catalog to page 6

©Epoch D Thread Mill is capable of simultaneous boring and threading. ©The above cutting conditions are for the nominal diameters stated in the table. Cutting conditions for other nominal diameters should be calculated taking into consideration the cautions on use (p. 15). ©The machinery should be a machining center equipped with NC (numerical control) equipment having a helical interpolation function. ©The feed rate stated in the above conditions table is the feed rate at the tool center during thread milling. In addition, the per-tooth feed rate is the numerical value at the cutting...

Open the catalog to page 7

incomplete thread and 2 complete threads Neck angle 0n : 1.7° *The neck angle (0n) of EDT-PT1(NPT1)-45-ATH is 0° (straight neck). : Stocked Items. Nominal diameter which requires pilot hole can not be used without larger pilot hole than the values shown in the table. O Cautions when using Epoch D Thread Mill for PT, NPT threads Outer diameter line C/e taper line passing through the apex of thread ridge) Since the reference tool diameter Dc and the tool tip diameter Dc' are different, it is necessary to correct the nominal diameter D1 and program. The nominal diameter D1 corresponds to the...

Open the catalog to page 8

[Note ©Epoch D Thread Mill is capable of simultaneous boring and threading. ©The above cutting conditions are for the nominal diameters stated in the table. Cutting conditions for other nominal diameters should be calculated taking into consideration the cautions on use (p.15). ©The machinery should be a machining center equipped with NC (numerical control) equipment having a helical interpolation function. ©The feed rate stated in the above conditions table is the feed rate at the tool center during tapping. In addition, the per-tooth feed rate is the numerical value at the cutting...

Open the catalog to page 9

Te c h n i c a l d a t a Field data of Epoch Thread Mill 01 Threading of hardened steels (M4×P0.7) Cutting conditions Work material：SKD11(60HRC) Tool：ET-0.7-8-PN n= 4,620min-1(vc=45m/min) v f =62mm/min（f z =0.015mm/t） Threading depth：8mm Blind hole Pilot hole dia.×Pilot hole depth： φ3.4 ×12mm Coolant：Air-blow Epoch Thread Mill Damaged on 10th hole Threading hole count (holes) Epoch Thread Mill after threading 50 holes Conventional after threading 10 holes. Machining up to 50 holes. NOT reached tool life. 02 Threading of sintered HSS material (M4×P0.7) Cutting conditions Work...

Open the catalog to page 10

05 Threading of superalloy (M6*P1) Cutting conditionS/H Work material : Inconel 718(40HRC) Tool: ET-1.0-12-PN n =2,420min-1(vc=35m/min) vf=56mm/min (fz=0.025mm/t) Threading depth : 12mm Blind hole Pilot hole dia.xPilot hole depth : 05.1x15mm Coolant : Water-base It is possible to thread superalloy which is difficult to tapping. 06 Threading of non-ferrous (Aluminium alloy A7075, Acrylic resin) (M6*P1) Work material : Aluminium alloy A7075, Acrylic resin Tool : ET-1.0-12-PN n=14,500min-1(vc=210m/min) vf=540mm/min (fz=0.04mm/t) Threading depth : 12mm Blind hole Pilot hole dia.xPilot hole...

Open the catalog to page 11

Te c h n i c a l d a t a Field data of Epoch D Thread Mill Simultaneous threading and drilling on hardened steels (M8×P1.25) Cutting conditions Work material：SKD11(Improved)(62HRC) Tool：EDT-1.25-16-TH n =2,060min-1(vc=40m/min) v f =47mm/min z =0.025mm/t）（f Threading depth：15mm Blind hole Coolant：Air-blow Epoch D Thread Mill Tool condition of Epoch D Thread Mill after machining 30 holes Wear condition is good with no chipping or damage! Threading hole count (holes) Machining up to 30 holes. NOT reached tool life. Simultaneous threading and drilling on hardened steels (M8×P1.25) Cutting...

Open the catalog to page 12

Simultaneous threading and drilling on stainless steels (M4×P0.7) Cutting conditions Work material：SUS304 Tool：EDT-0.7-10-TH n=3,600min-1(vc=35m/min) v f =49mm/min z =0.015mm/t）（f Threading depth：10mm Blind hole Coolant：Water-base Epoch D Thread Mill after threading 600 holes. Machining up to 600 holes, NOT reached tool life. Simultaneous threading and drilling on titanium alloys (M4×P0.7) Cutting conditions Work material：Ti-6Al-4V Tool：EDT-0.7-10-TH n=3,600min-1(vc=35m/min) v f =49mm/min z =0.015mm/t）（f Threading depth：10mm Blind hole Coolant：Water-base Epoch D Thread Mill after...

Open the catalog to page 13