Subrack F60
26Pages

HIMatrix Safety-Related Controller HIMA Paul Hildebrandt GmbH Industrial Automation

All HIMA products mentioned in this manual are protected by the HIMA trade-mark. Unless noted otherwise, this also applies to other manufacturers and their respective products referred to herein. HIMax®, HIMatrix®, SILworX®, XMR® and FlexSILon® are registered trademarks of HIMA Paul Hildebrandt GmbH. All of the instructions and technical specifications in this manual have been written with great care and effective quality assurance measures have been implemented to ensure their validity. For questions, please contact HIMA directly. HIMA appreciates any suggestion on which information should...

Structure and Use of this Manual Target Audience Formatting Conventions Safety Notes Operating Tips Intended Use Environmental Requirements ESD Protective Measures Residual Risk Safety Precautions Emergency Information Product Description Safety Function Equipment, Scope of Delivery Type Label Product Data Product Data GEH 014 Mounting Mounting the GEH 01 Subrack in Zone 2 Replacing Fans

Introduction This manual describes the technical characteristics of the subrack and its use. It provides information on how to install, start up and configure the module. Structure and Use of this Manual The content of this manual is part of the hardware description of the HIMatrix programmable electronic system. This manual is organized in the following main chapters:          Introduction Safety Product Description Start-up Operation Maintenance Decommissioning Transport Disposal This manual usually refers to the plug-in cards of a modular controller as modules. Modules is also...

Target Audience This document addresses system planners, configuration engineers, programmers of automation devices and personnel authorized to implement, operate and maintain the modules and systems. Specialized knowledge of safety-related automation systems is required. Formatting Conventions To ensure improved readability and comprehensibility, the following fonts are used in this document: Bold Italics Courier RUN Chapter 1.2.3 To highlight important parts Names of buttons, menu functions and tabs that can be clicked and used in the programming tool. For parameters and system variables...

Operating Tips Additional information is structured as presented in the following example: The text corresponding to the additional information is located here. Useful tips and tricks appear as follows: The tip text is located here.

Safety All safety information, notes and instructions specified in this document must be strictly observed. The product may only be used if all guidelines and safety instructions are adhered to. This product is operated with SELV or PELV. No imminent risk results from the product itself. The use in Ex-Zone is permitted if additional measures are taken. Intended Use HIMatrix components are designed for assembling safety-related controller systems. When using the components in the HIMatrix system, comply with the following general requirements. Environmental Requirements Requirement type...

Residual Risk No imminent risk results from a HIMatrix system itself. Residual risk may result from:  Faults related to engineering  Faults related to the user program  Faults related to the wiring Safety Precautions Observe all local safety requirements and use the protective equipment required on site. Emergency Information A HIMatrix system is a part of the safety equipment of a site. If a device or a module fails, the system enters the safe state. In case of emergency, no action that may prevent the HIMatrix systems from operating safely is permitted.

Product Description The subrack is intended for being equipped with modules of the F60 system. Slots 1 and 2 are reserved for the power supply module and central module, respectively. Any type of F60 modules can be plugged in to slots 3...8. Safety Function No safety function is performed by the subrack. Equipment, Scope of Delivery The following table specifies the available components: Designation GEH 01 GEH 014 Description Subrack (earth grid, 2 fans, slots for power supply module, central module and 6 I/O modules) Subrack (earth grid, 2 fans, slots for power supply module, central...

Housing, Earth grid, Backplane PCB (printed circuit board), Guiding rails, and 2 fans. The backplane PCB contains connectors for connecting the power supply module and the F60 modules. The plug connections for the power supply of the fans are located on the left bottom side of the PCB backplane.

Connection of the Central Module Current Connections for the Fans Connection of the Power Supply Figure 3: The subrack is completed mounted, including the earth grid, backplane PCB, guiding rails and 2 fans.

Product Data Specifications Material Horizontal pitch Modules Connector Type of connection Fan Humidity Ambient temperature Storage temperature Dimensions Weight Table 4: Aluminum, anodized, partially coated 40 HP (1 HP = 5.08 mm) in accordance with DIN EN 60287-4, 4 HP each in accordance with DIN EN 60603-2, Type C, 96-pole Connector Part number: 39 2003001 < 95 % relative humidity, non-condensing 0...60 °C -40...+85 °C 40 HP, 7 RU W x H x D: 259 x 310 x 228 mm approx. 1.5 kg Product Data Product Data GEH 014 The GEH 014 model variant is intended for use in railway applications. The...

Start-up This chapter describes how to install the GEH 01 subrack. Mounting To ensure faultless operation, choose a suitable mounting location for the subrack in accordance with the operating requirements. Observe the following points when mounting the module:  Mount the subrack on horizontal DIN rails to ensure effective cooling.  A distance of at least 100 mm above and below the subrack must be maintained.  Do not mount the subrack above heating equipment or any heat source. For more information, refer to HIMatrix system manual for the modular system (HI 800 191 E). Mounting the GEH 01...

4 Start-up The subrack is additionally equipped with the label represented below: HIMA HIMatrix Paul Hildebrandt GmbH A.-Bassermann-Straße 28, D-68782 Brühl II 3 G Ex nA II T4 X 0 °C < Ta < 60 °C Besondere Bedingungen X beachten!