Machine needle shut-off nozzle type HP pneumatically or hydraulically controlle
9Pages

HP-Nozzle, machine-side actuator, Installation & Service Instructions Safety instructions This symbol indicates explanations about important matters. Failure to read these or false handling could result in injury or damage. Please pay attantion to the following safety instructions and precautions Handling • Installation and servicing to be only carried out by protected personnel according to the installation and service instructions. • Nozzle can become extremely hot. Full face protection and heat resistant gloves must be worn. Damage precaution • Do not drop the nozzle or exert it to...

HP-Nozzle, machine-side actuator, Installation & Service Instructions Installation instructions Read safety instructions! Legend: with Hand inspection smear with high temperature lubricant temperature equalisation tool Note: Nozzle is delivered pre-assembled. The following instructions are for installation on the machine. Tools required: Hexagonal wrench, allen key, ring spanner, socket wrench, pliers, punch. See chapter Assembly for tool sizes and torques. Installation Steps - Adaption with pressure screws 5. Note: the following steps are valid for a pre-assembled nozzle only 1. 2. 3. 4....

HP-Nozzle, machine-side actuator, Installation & Service Instructions B) 3. 1. über Kreuz 2. 1. Check surfaces and threads 2. Smear adapter thread with high temperature lubricant 3. Mount adapter; await temperature equalisation and tighten acc. to machine handbook 4. Tighten two screws crosswise C) 1. 2. 3. 4. 1. + 5. Screw nozzle onto the adapter until contact Screw in tip further until contact Loosen the two previously tightened screws by four rotations. Screw in tip approx. 180° further Rotate clockwise 5. Align lever with stroke bar! 2. + 4. 5. Align: Screw nozzle clockwise further onto...

HP-Nozzle, machine-side actuator, Installation & Service Instructions Torque HP1 HP2 1. pass handtight handtight handtight 2. pass 7 Nm 15 Nm 35 Nm 3. pass 10 Nm 22 Nm 45 Nm 4. pass E) HP0 12 Nm 25 Nm 50 Nm 1. Tighten all screws in a crosswise fashion 2. Set stroke bar range (see table below) and couple with lever crosswise 1. HP0 F) HP2 Maximum lever force 800N 900N 2000N Minimal lever range 2. HP1 14 mm 16mm 22 mm 1. Mount heater band (1a) and temperature sensor (1b) 2. Tighten tip with torque according to chapter Assembly* 1b. * Tip is already tight when mounting step D) has been...

HP-Nozzle, machine-side actuator, Installation & Service Instructions Service instructions Read safety and cleaning instructions! Assembly Note: Grease all threads with high temperature paste! Disassembly A) - B) A) 360° x 2 1. 2b. 3. 2a. 2c. Removing the nozzle from the machine: 1. Heat nozzle to operating temperature 2. Remove stroke bar (2a.), sensor (2b.) and heater band (2c.) 3. Loosen screws (two rotations) B) 2.* 3a. 1a. 4a. 3b. 1b. 1c. 4b. 5b. 5a. 1. Remove tip (1a.), Needle (1b.) and holding pin (1c.) 2. Remove bushing. *If you have difficulty removing the bushing we recommend...

HP-Nozzle, machine-side actuator, Installation & Service Instructions Recommended disassembly tool Option: Our disassembly tool eases the needle bushing removal. 1. 2. 3. Holding pin must be removed or min. 5 mm screwed out Position removal nut Screw in removal screw until the bushing is removed lubricate 3. 1. 2. Assembly Note: Bushing bore must be aligned with holding pin. Tighten the holding pin with moderate strenght (ca. 8Nm). The end position of the holding pin is approx. 0.5 mm away from the body unit. More information at www.herzog-ag.com Cleaning instructions To clean the nozzle we...

HP-Nozzle, machine-side actuator, Installation & Service Instructions Parts subject to wear / ordering spare parts Your contact information: Company Street City / Zip Contact Tel. / Fax E-Mail Lasered nozzle identity no.: please insert here Quantity Part (for part name, see chapter Assem bly) Send to: herzog systems ag CH-9230 Flawil / Switzerland Tel. +41 (0) 71 394 19 69 / Fax +41 (0) 71 394 19 60 www.herzog-ag.com / info@herzog-ag.com herzog systems ag Tel. +41 (0)71 394 19 69 Fax. +41 (0)71 394 19 60 www. herzog-ag. com info@herzog-ag. com 9 Version 0.5