Precision Ring and Track System This data sheet interacts with DTS driven track system This data sheet interacts with DTS Catalogue No. 8 DTS Components HepcoMotion® supply a comprehensive range of components and assemblies to enable the 25-351 and 44-612 size track systems to be incorporated into customers own designs complete with drive facility. Many of the components shown in this datasheet can also be used for other sizes of track system. The components are well proven having been used for many years in the HepcoMotion DTS, a complete and ready to use driven track system highly recommended for customers able to use this fully assembled standard product. This datasheet contains details and dimensions for the individual assemblies available. For more information or advice to suit a particular application, please contact Hepco’s technical department. Idler Pulley Assembly Trip Latch Assembly Belt Flight Assembly Locking Cam Assembly Drive Pulley Assembly Carriage Assembly Drive Belt Carriage Locking Shaft Track Support Beam Extrusion Carriage Locking System Assembly Oval Top Plate Assembly Oval Bottom Plate Assembly Locking Lever Assembly Drive Shaft Assem

No. 8 DTS Components Carriage Assembly A D 2 x M5 Tapped Holes For attachment of locking cam U Ø5 dowel hole For attachment of locking cam 4 x V Customer Mounting Holes 2 x M5 Tapped holes For attachment of fixed/trip latch G Part Number

No. 8 DTS Components Trip Latch Assembly Trip load setting screws (adjust both sides) 2x M5x20 Button head screws D Part Number Fixed Latch Assembly 2 x M5x20 Button head screws Part Number

No 8 DTS Components Sensor Block Assembly Part Number

No 8 DTS Components Locking Cam Assembly Part Number

No 8 DTS Components Basic Carriage Locking Assembly D Slot blocks to suit DTSBEX Cylinder Assembly Bearing Cylinder Assembly Assembly

No 8 DTS Components Locking Lever Assembly A B C M6x30 Cap head screw Part Number Note: 1. Up to 8 locking levers on one shaft can be operated by a single cylinder depending on carriage spacing, please contact Hepco’s technical department. Carriage Locking Shaft NIM25SS316 Specify length to suit

No. 8 DTS Components Drive Pulley Assembly Part Number Teeth profile to suit

No. 8 DTS Components Idler Pulley Assembly Part Number

No. 8 DTS Components Drive Shaft & Bearing Cartridge Assembly Ø140 Ø124 30° 60° 2 x M8x12 Cap head screws 10 x M6x16 Countersunk screws Part Number

No. 8 DTS Components Idler Shaft & Bearing Cartridge Assembly DTSISBCSA 2 x M8x12 Cap head screw 10 x M6x16 Cap Head Screw 6 holes M6x1

No 8 DTS Components Top Plate Oval Assembly MCS 60x60 section 0-132-6060. Please see separate Hepco MCS catalogue. Feature to suit DTSDS25/30BCSA or DTSISBCSA Part Number Note 1. Ref dimensions are such as the holes are drilled on assembly

Bottom Plate Oval Assembly MCS 60x60 section 0-132-6060. Please see separate Hepco MCS catalogue. Part Number Note 1. Ref dimensions are such as the holes are drilled on assembly

No. 8 DTS Components Top Plate Rectangular Assembly Tapped holes to suit TR25 351 90° (M5) E G Feature to suit DTSDS25/30BCSA or DTSISBCSA Part Number

Additional Slot blocks are available on request, see page 19 DTSBEX - Track beam support extrusion End section machined to provide flush mounting surface with plates. See page 19 for more details. A Tapped holes to suit TR44 612 90° (M6) Feature to suit DTSDS25/30BCSA or DTSISBCSA Note 1. Ref dimensions are such as the holes are drilled on assembly

Bottom Plate Rectangular Assembly Additional Slot blocks are available on request, see page 19 DTSBEX - Track beam support extrusion End section machined to provide flush mounting surface with plates. See page 19 for more details. Note 1. Ref dimensions are such as the holes are drilled on assembly

Drive Belt Oval Circuit L min Rectangular Circuit W min Belt Flight Pitch B min Part Number Note 1. Pitches are available in increments of 10mm from the minimum value stated above, value will correspond to carriage spacing. 2. Belt flights come with the drive belt as standard, please state number required and pitch when ordering, this will correspond to the number of carriages required. 3. For more details and dimensions of belt flights, please see page 18.

No 8 DTS Components Belt Flight Assembly DTSBFSA 48 20 Rubber Bush Reduces shock loading to belt connection during rapid motion profiles Slide Attachment Profile Length to suit application (max 6000mm) Part Number Notes 1. Dimension from last hole to the end of the slide can be changed to suit design, please specify when ordering. 2. Supplied complete with set screw to secure slide attachment profile in place.

No 8 DTS Components Track Beam Support Extrusion/m DTSBEX Length to suit application (max 6000mm) 80 10 20 6 12 Notes: 1. Customers can machine ends as shown to expose secondary T slot for attaching top plate by means of slot block part no 1-242-1031. 2. Tolerance to suit top plate thickness. Mating top surfaces should be flush. Ordering details To order any of the assemblies shown in this document, state the part number shown, followed by the quantity required. For more information or advice with a particular application, please contact Hepco’s technical department. Ordering Example Description...