DATA SHEET PTP/IEEE 1588 Grandmaster Clock and NTP Time Server with high accuracy GPS receiver, OCXO or Rubidium oscillator 1 Bd d’Armor – 22300 LANNION - FRANCE [email protected] 1 © 2015 All Rights Reserved. All specifications subject to change without Notice.

HEOL-T200 : PERFORMANCE and EASY INTEGRATION The HEOL-T200 PTP IEEE-1588 Grandmaster Clock / NTP Time server with GPS Clock has been designed to provide accurate timing information trough an Ethernet link (using Precision Time Protocol), for Network synchronization and measurement applications, without the need to be connected to external Network, hence preserving your Network insulation. Based on a high performance 14 channels GPS chipset with very high accuracy, and TRAIM algorithm, accuracy is guaranteed with only one GPS satellite tracked. It enables also fast start-up times in very hard...

DATA SHEET An isolated event input allows you to time-stamp events from external systems, with very high accuracy (±100 nanoseconds, refer to UTC atomic clock). The TimeStamp information is reported through RS232, SNMP trap, E-mail or Broadcast frame. Alarm relay is available, for driving your external systems in case of failure of the T200. Alarms are displayed through SNMP traps (Ethernet interface) or through RS232. SNMP can also be used to configure T200 parameters (instead of http web server). A highly accurate pps (TOP) signal is available on SUB-D9 or I/O connector (polarity, period, length,...

DATA SHEET GPS antenna Remote interface +NMEA OCXO or Rubidium Clock Event inputs External Events Sync outputs User systems PTP + NTP (synchro and events) HTTP (config) SNMP (alarms and events) SMTP (E-mail) Automated systems T200 synoptic and external links Note : Heol Design is not responsible for the operation or failure of operation of GPS satellites or the availability of GPS satellite signals. 1 Bd d’Armor – 22300 LANNION - FRANCE [email protected] 4 © 2015 All Rights Reserved. All specifications subject to change without Notice.

DATA SHEET Type Sensitivity Overdertermined clock mode (self survey) Time Accuracy (pps) Time to First Fix (cold start) Warm up time Active antenna voltage Timing Generator 14 channels -160dBm (tracking) 24 hours Timing Ethernet protocol SNTP V4, NTP Broadcast/Unicast (200 requests per second maximum), 200 000 NTP Clients @ 1024s ±15 ns rms (1σ) < 45 seconds (90%) < 15 minutes for full accuracy 5V or 3V, configurable PTP IEEE1588-2008 : - UDP/IPv4 - Addressing mode : Multicast & Unicast - Delay Mechanism : End-to-End - Operation : Two Step Clock - Sync & Announce Intervals : 1, 2, 4, 8, 16, 32,...

Environmental Operating Temperature From 0/50°C to -40/+85°C, depending _-depth with N connecto_ ■ According to C € directive, the HEOL-T200 module has passed the following tests : > EN55022/55011 class B : conducted and radiated emissions. > EN61000-4-2: Immunity to electrostatic discharges. > EN61000-4-3: Immunity tests on electromagnetic fields radiated at radio-electrical frequencies, with lOV/m electromagnetic field. > EN61000-4-4: Immunity to rapid transients. > EN61000-4-6: Immunity tests on conducted interference, induced > EN61000-4-8: Immunity to Power frequency magnetic field (30 >...

DATA SHEET T200 19’’ 1U Rack rear view (with ‘N’ antenna connector) 3&4 pins : Alarm relay or PPS/TOP output on Static relay (option PPSREL) 1&2 pins : Event input #1 5&6 pins : PPS/TOP RS422 output or IRIG B003 output (option IRIG) or Event input #2 (option EVENT2) I/O connector details 1 Bd d’Armor – 22300 LANNION - FRANCE [email protected] 7 © 2015 All Rights Reserved. All specifications subject to change without Notice.

DATA SHEET ORDERING PART NUMBER T200R-100ns-AC-I/O-OCXOSR • Housing R: 19’’Rack C: Compact • PTP accuracy • Power DC : 14 to 60V DC/POE: DC+Power Ethernet AC : 110 to 250V (Rack only) • I/O option I/O connector mounted (blank : not mounted) • Oscillator option OCXOSR : standard (0 / +50°C) OCXOMR : medium (-20 / +65°C) OCXOHR : high (-40 / +70°C) RUB : high stability Rubidium (Rack in AC version) - 0 / +50°C If other options are needed, just add the part number of these options at the end of the T200 part number : -422 for RS422 serial port instead of RS232 -EVENT2 for secondary Event input -IRIG...