N016, Lassen iQ / SQ Improved replacement GPS receiver 1 Bd d’Armor – 22300 LANNION - FRANCE Call: +33 (0)296 484 605 – Fax: +33 (0)296 484 463 E-mail: [email protected] Copyright 2008 All Rights Reserved

BEST PERFORMANCE HEOL DESIGN has produced a new GPS receiver board, the “HEOL-N016”, which is based on the Trimble Copernicus high performance GPS chip set. This OEM board is designed for use in embedded and industrial applications requiring high accuracy positioning and timing information. It can also be used as a replacement and upgrade for users of the Trimble Lassen iQ receiver board. ADVANTAGES: Ultra-high sensitivity of -160dBm, enabling high performance acquisition and tracking in urban canyon and signal obscured environments. SBAS support (WAAS, EGNOS), for improved Horizontal and Altitude...

SUMMARY OF THE CHARACTERISTICS: Performances: Receiver Update speed Accuracy Horizontal (w SBAS) Altitude (w SBAS) Speed Time (pps) Initial acquisition time Cold (Time to First Fix) Warm start Hot start Reacquisition signal after signal lost Altitude Speed Acceleration Operating Temperature Storage Temperature 12 channels, -160dBm TSIP ⇒ 1Hz ; NMEA ⇒ 1Hz <2 meters (50%), <4 meters (90%) <3 meters (50%), <5 meters (90%) 0,06 m/sec (nominal)* ±60 ns < 39 seconds (90%)* < 35 seconds (90%)* < 3 seconds (90%)* < 2 seconds (typical)* < 18 000 m < 515 m/sec maximum 4 g (39,2m/sec ) -40/+85 °C -55/+105°C...

Physical characteristics: a) N016 without fixing pins: HEOL DESIGN 1 Bd d'Armor - 22300 LANNION - FRANCE E-mail: [email protected] Copyright 2008 All Rights Reserved

b) 3 fixing pins allow you to solder firmly the N106 board on your mother board. These pins can be right angle (surface mount) : (other heigths available on request) HEOL DESIGN 1 Bd d'Armor - 22300 LANNION - FRANCE E-mail: [email protected] Copyright 2008 All Rights Reserved

EMC compatibility The HEOL-N016 board has successfully completed compliance testing against the following standards listed below: (In accordance with the directive). EN55022 class B (conducted and radiated emissions) dated January 1999, with 10dB margin. EN61000-4-3 published in 2002: “Immunity tests on electromagnetic fields radiated at radio-electrical frequencies”, with 10V/m electromagnetic field. EN61000-4-6 published in February 1997: “Immunity tests on conducted interference, induced by radio-electrical fields”. EN61000-4-4 (Immunity to rapid transients) dated June 1995, with 2kV transients....

Connectors description 8 pin 1.27 mm male header: 8 V Backup (do no connect for on board back-up capacitor option) Antenna: Hirose HFL or transition cable to SMA. Factory settings of the serial ports The two communication ports (3.3V level) are set as standard as follows: Port 1: • Input: TSIP protocol, 38400 Baud, 8 bits, no parity, 1 stop bit. • Output: TSIP protocol, 38400 Baud, 8 bits, no parity, 1 stop bit. Port 2: • Input: NMEA protocol, 4800 Baud, 8 bits, no parity, 1 stop bit. • Output: NMEA protocol, 4800 Baud, 8 bits, no parity, 1 stop bit. 1 Bd d’Armor – 22300 LANNION - FRANCE Call:...

Ordering part number The factory standard part number is HEOL-N016-V1-HS2. However, customer can request several options, as described hereafter Antenna connector: • H : Hirose HFL (default) • A : SMA on cable Optional on board BackUp Battery Capacitor (leave blank if not required) Fixing pins: • S1 : 5.08mm Straight • S2 : 5.59mm Straight (default) • S3 : 6.35mm Straight • R : Right angle • blank : no fixing pin The specifications in this document are subject to change without notice. Heol Design is not responsible for the operation or failure of operation of GPS satellites or the availability...