Assembly and Service Instructions Telescopic Steel Covers
8Pages

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS global excellence in machine protection

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS Dear customer, We thank you very much for choosing to buy a telescopic steel cover from Hennig. Please read the following sections on installation, maintenance, and care, so that your steel cover can be used for a long time, reliably and without breakdowns. Hennig telescopic steel covers serve the purpose of protecting sensitive guiding systems on processing machines from swarfs, dust, or liquids. Your Hennig steel cover is generally custom-manufactured and therefore may deviate in its details from the descriptions and...

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS 6. Covers with holes in all rear walls and in the front cover panel (FCP) must be raised with transport rods. Prior to lifting, these rods must be secured in such a way that the cover panel or the burden chains or lifting straps cannot slide out. 7. Please always make sure that burden chains, lifting straps, or rope hooks, do not damage the cover. 8. When fitting the steel covers, the lateral guide slides should not collide with the surface of the guide track, to avoid damage. 9. The steel covers must always be mounted onto the...

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS III. “Venetian” Blind Covers with Guide Rails 1. 2. 3. 4. When installing the guide rails, make sure they are positioned in parallel. Press the panels into the guide rails. Make sure that they connect at the correct angle and avoid tilting. Fasten the front and rear box of the “Venetian” blind cover in compressed position. 1) Pull out the first box to the stopping point Wiper Rear wall IV. Steel Covers with Overtravel Mechanism The overtravel protection and the latching panels must be adjusted in such a way that a longterm and...

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS 3. Covers with Scissors (Illustration 6) 3.1 Release the mounting of the largest and smallest boxes. 3.2 Push the steel covers together. 3.3 Remove the cover from the machine and set it carfully on its rear side. 3.4 Remove the locking ring from the scissor pins and pull the scissor up and away. 3.5 Set the cover in the compressed position back onto the guide track. 3.6 Pull out the uppermost (largest) box to the position of the stop. When proceeding, hold the subsequent boxes firm ly in place. 3.7 Press lightly against the wiper...

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS D. PUTTING THEM INTO OPERATION Prior to being sent, your Hennig telescopic steel cover was coated with a corrosion-protection oil and packaged in a plastic film. This protects your steel cover to a major extent against corrosion during transport and over longer-term storage. Please oil the entire steel cover prior to putting it into operation. After installing the cover, a functional test must absolutely be performed: Operate the tool slide or machine table first at low speed. In doing so, check that the covers does not bump into...

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS for the entire cover, if their buffering effect has deteriorated significantly. Scissors must be replaced if they become deformed or if they move too freely on the scissor pins. Scissors must be replaced if they have become worn out. Repairs to scissor bracket systems cannot be self-done, for reasons of safety. When needed, the covers should be sent to Hennig for maintenance or general overhaul. Faulty overtravel mechanism must be completely replaced on both sides, along with the snap-in plates. Newly added overtravel mechaninsm...

ASSEMBLY AND SERVICE INSTRUCTIONS FOR TELESCOPIC STEEL COVERS A company of the GOELLNER Group, Rockford IL, USA. C6 means: Replacing wipers directly on the machine without dismantling the telescopic steel cover. 1. 2. 3. 4. 5. Remove old spring clamps using disassembly tool # 200.00040. Hold the tool with the handle diagonally upwards. Place the plastic roller of the tool onto the box panel. Hook both claws of the tool into the facing nose of the spring clamps. Then carefully lift the spring clamps out by applying pressure on the handle. If no disassembly tool happens to be available, the...