DATA SHEET labVF6-Iso II labVF6-Iso II is a 6-channel HEADlab input module with HEADlink 2.0 transmission protocol for connecting voltage and IEPE/ICP sensors. The six high-impedance inputs are electrically isolated from each other and also from the digital HEADlink interface, enabling the module to be used even in electromagnetically demanding environments. HEAD acoustics GmbH Code 3757, Rev. 04, subject to change, last update: 01/26

6-channel HEADlab input module with HEADlink 2.0 labVF6-Iso II provides six high-impedance inputs that are electrically isolated from each other. Electrical isolation prevents ground loops and extends the range of application to electromagnetically demanding environments. In addition, the module is characterized by a high input impedance, switchable lowpass filters, and flexibly adjustable sampling rates of 2.048 kHz to 204.8 kHz. Electrical isolation of the inputs from each other and also from the digital HEADlink interface High input impedance › 10 MΩ DC, e.g., for resolvers › 1 MΩ AC, for...

DETAILS Electrical isolation Power supply labVF6-Iso II provides 6 BNC inputs for direct connection of voltage or IEPE/ICP sensors. To prevent ground loops, each input is electrically isolated from both the grounds of the other inputs and the HEADlink interface. This enables sensors without case isolation to be used in electromagnetically demanding environments. labVF6-Iso II does not require a dedicated power supply, as the input module and all connected modules (e.g., a labCTRL II.1 controller with up to ten modules) are powered by the controller, the compact system, or other connected devices....

CONNECTION OF SENSORSVia BNC > Voltage or IEPE/ICP sensors (TEDS) > BHM III.3 mobile headset microphone for binaural recordings > HSU III.2 artificial head microphone CONTROL / POWER SUPPLY CONNECTION TO CONTROLLER / FRONTEND / SYSTEMHEAD/znk Protocol 2.0 via HEAD/znk > /abCTRL II.1 controller > /abHSU high-end 2-channel frontend (from firmware version 2.1) > HMS V digital head measurement system (from firmware version 2.1) POWER SUPPLYVia HEAD/znk HEAD/znk Protocol 1.0 via HEAD/znk > /abCTRL I.2 and /abCTRL I.1 controllers > /abHSU 2-channel frontend (up to firmware version 2.1) > HMS V digital...

3757 /abVF6-Iso II 6-channel HEAD/ab input module with HEAD/ink 2.0 transmission protocol for connecting voltage and IEPE/ICP sensors Hardware AccessoriesRequired (One of the Controllers Listed Below, ...) 3704 HEAD acoustics GmbH 5 Code 3757, Rev. 04, subject to change, last update: 01/26

Further modules of ArtemiS SUITE (see ArtemiS SUITE Overview data sheet) HEAD acoustics GmbH 6 Code 3757, Rev. 04, subject to change, last update: 01/26

Plug connector 1 x LEMO 8-pin HEAD/ink version HEAD/ink 1.0, HEAD/ink 2.0 Maximum cable length 60 m HEAD acoustics GmbH 7 Code 3757, Rev. 04, subject to change, last update: 01/26

1 Valid for: ambient temperature 23 °C, 73.4 °F (±3 °C, ±5.4 °F ), operating duration >1 h. Vibration excitation of the device may cause deviations. All measurement ranges are calibrated at the factory. In addition, the measurement ranges 300 mVP to 30 Vp can be calibrated in the accredited calibration laboratory of HEAD acoustics GmbH in accordance with DIN EN ISO 17025. HEAD acoustics GmbH 8 Code 3757, Rev. 04, subject to change, last update: 01/26

1 Valid for: ambient temperature 23 °C, 73.4 °F (±3 °C, ±5.4 °F ), operating duration >1 h. Vibration excitation of the device may cause deviations. All measurement ranges are calibrated at the factory. In addition, the measurement ranges 300 mVP to 30 Vp can be calibrated in the accredited calibration laboratory of HEAD acoustics GmbH in accordance with DIN EN ISO 17025. There is no standardized calculation method for the term "dynamics". This is why the Signal-to-Noise Ratio value (SNR or S/N) is specified for ZabVF6-Iso II. This value is calculated based on the level of a sinusoidal tone with...