P126TI
4Pages

DOOSAN INFRACORE GENERATOR ENGINE Ratings Definitions The power ratings of Emergency Standby and Prime are in accordance with ISO 8528. Fuel Stop power in accordance with ISO 3046. Electric power (kWe) must be considered cooling fan loss, alternator efficiency, altitude derating and ambient temperature. STANDBY POWER RATING is applicable for supplying emergency power for the duration of the utility power outage. No overload capability is available for this rating. A standby rated engine should be sized for a maximum of an 80% average load factor and 200 hours of operation per year. This includes less than 25 hours per year at the Standby Power rating. PRIME POWER RATING is available for an unlimited number of hours per year in variable load application. Variable load should not exceed a 70% average of the Prime Power rating during any operating period of 24 hours. The Total operating time at 100% Prime Power shall not exceed 500 hours per year. A 10% overload capability is available for a period of 1 hour withing a 12 hour period of operation. Total operating time at the 10% overload power shall not exceed 25 hours per year. ◎ GENERAL ENGINE DATA o Engine Model o Engine Type o Bore x stroke o Displacement o Compression ratio o Rotation o Firing order o Injection timing o Dry weight o Dimension (LxWxH) o Fly wheel housing o Fly wheel o Number of teeth on flywheel © ENGINE MOUNTING Counter clockwise viewed from Flywheel 1-5-3-6-2-4 16°±1° BTDC 910kg (with Fan) 1,384 x 1,109 x 1,195 mm SAE NO.1M Clutch NO.14M 152 Maximum Bending Moment at Rear Face to Block 1325 N • M Maximum Back Pressure 5.9 kPa Maximum Intake Air Restriction . With Clean Filter Element 2.16 kPa . With Dirty Filter Element 6.23 kPa o Max. static pressure after Radiator 0.125 kPa Printed in September 2015 Medium Engine Main Feature Development

Water circulation by centrifugal pump on engine. o Cooling method o Coolant capacity o Coolant flow rate o Pressure Cap o Water T emperature - Maximum for standby and Prime - Before start of full load o Water pump o Thermostat Type and Range o Cooling fan o Max. external coolant system restriction © LUBRICATION SYSTEM Fresh water forced circulation Engine Only : Approx. 19 lit., With Radiator : Approx. 51 lit. (standard) liters / min 49 kPa 103 °C 40.0 °C Centrifugal type driven by Gear Wax - pellet type, Opening temp. 71°C , Full open temp. 85°C Blower type, Plastic , 755 mm diameter, 7...

© VALVE SYSTEM o Type o Number of valve o Valve lashes at cold o Valve timing Overhead valve type Intake 1, exhaust 1 per cylinder Intake 0.3mm , Exhaust 0.3mm Opening Close -. Intake valve -. Exhaust valve © PERFORMANCE DATA Prime Power Standby Power o Governed Engine speed rpm 1500 1800 1500 1800 o Engine Idle Speed rpm 800 800 800 800 oOver speed limit rpm 1650 1980 1650 1980 o Gross Engine Power Output kW 241 278 272 298 o Break Mean effective pressure Mpa 1.75 1.68 1.97 1.80 o Mean Piston Speed m/s 7.75 9.3 7.75 9.3 o Specific fuel consumption 25% load liters/hr 16.4 20.3 18.3 21.5 o...

◆ CONVERSION TABLE in. = mm x 0.0394 PS = kW x 1.3596 psi = kg/cm2 x 14.2233 in3 = lit. x 61.02 hp = PS x 0.98635 lb = kg x 2.20462 kW = Kcal/sec x 0.239 lb/ft = N.m x 0.737 U.S. gal = lit. x 0.264 kW = 0.2388 kcal/s lb/PS.h = g/kW.h x 0.00162 cfm = m3/min x 35.336 Mpa = Pa x 1000 = bar x 10 Doosan Infracore Co., Ltd. 21st Floor, Doosan Tower, 18-12, Euljiro 6-ga, Jung-gu, Seoul, Korea. TEL : +82-2-3398-8400 / FAX : +82-2-3398-8509 E-mail : enginesales@doosan.com Web site : www.doosaninfracore.com ※ Speccifications are subject to change without prior notice Printed in September 2015 Medium...