Ear Hose Clamp Air Tool
Ear Hose Clamp Air Tool
Pneumatic fitting tool designed for tightening metal ear hose clamps. It includes a TPU protective bumper, four power modules, and a counterbalance hook. The closing force is adjustable via incoming air pressure.
General Properties
- Hose Clamp Type: Metal Ear Clamp
- Weight: 1.15 kg (2.54 lb) ± 2%
- Dimensions: Length 355 mm (13.98 inch), Height 106 mm (4.17 inch), Width 60 mm (2.36 inch)
- Jaw Width: 44 mm (1.73 inch)
- Jaw Closing Range: 2 mm (0.079 inch) to 13 mm (0.51 inch)
- Body Diameter: 54 mm (2.13 inch)
- Jaw Height: 17 mm (0.67 inch)
- Air Inlet Thread Size: 1/8” Inch BSP
- Lanyard Hole Diameter: 10 mm (0.39 inch)
Mechanical Properties
- Jaw Closing Force varies with pressure:
- 2 Bar (29.0 psi): 872 N (89 Kgf, 196 Lbf)
- 3 Bar (43.5 psi): 1570 N (160 Kgf, 353 Lbf)
- 4 Bar (58.0 psi): 2168 N (221 Kgf, 487 Lbf)
- 5 Bar (72.5 psi): 2833 N (289 Kgf, 637 Lbf)
- 6 Bar (87.0 psi): 3409 N (347 Kgf, 766 Lbf)
- Closure force depends on a suitable compressed air supply flow rate >50L/min
Operating Details
Further details on tool setup and maintenance are available in the original instructions. Contact HCL for spare parts and repair.
Important Notice to User
- Storage: Store in a dry environment and in the original carton when not in use.
- Warranty: Products are warranted to meet specifications if stored, used, and maintained as per instructions. Only replacement or refund of affected parts is considered if the product does not conform to the warranty.
- Limitation of Liability: HCL is not liable for any damage or loss from product use, except where prohibited by law.
- Product Use: Users must determine product suitability for their tasks. Contact HCL for the latest data.
Catalog excerpts
Technical Data Sheet Hose Clamps REF:TDS PHCT-J02-B04-H02 RevOl.docx Ear Hose Clamp Air Tool Suitable For: Metal Ear Clamps 4 power modules and counterbalance hook. Closing force can be set by adjusting the incoming air General Properties COMPANYWITH QUALITY SYSTEM CERTIFIED BY DNV Registered Office, Clamping House, First Avenue, Westfield Industrial Estate, Radstock, BA3 4BS, UK VAT no 639389486 Registered No 2860032 Tel: +44 (0)1761 417714 Email: [email protected] Web: www.hclfasteners.com
Open the catalog to page 1
Technical Data Sheet Hose Clamps REF:TDS PHCT-J02-B04-H02 RevOl.docx General Properties Continued COMPANYWITH QUALITY SYSTEM CERTIFIED BY DNV Registered Office, Clamping House, First Avenue, Westfield Industrial Estate, Radstock, BA3 4BS, UK VAT no 639389486 Registered No 2860032 Tel: +44 (0)1761 417714 Email: [email protected] Web: www.hclfasteners.com 1 The closure force is dependent on suitable compressed air supply flow rate >50L/min 2 Force measured using a 50KN calibrated Zwick Tensometer Further Operating Details, including tool setup, and maintenance can be found in the original...
Open the catalog to page 2
Technical Data Sheet REF:TDS PHCT-J02-B04-H02 Rev01.docx Important Notice to User Storage: Tool should be installed and used in a dry environment. When not in use store in a cool dry area in original carton. Original Tool Carton with generic tool example shown Warranty: HCL warrants that all products when stored, used and maintained in accordance with HCL’s written instructions will meet or exceed the above specification. HCL makes no other warranties or conditions, expressed or implied, including, but not limited to, any implied warranty or condition of merchantability or fitness for a particular...
Open the catalog to page 3All HCL catalogs and technical brochures
PLAIN BAND CLAMPS2 Pages
SM-FT-1001 Banding Tool20 Pages
Smart Band3 Pages
