P 333 3:1 HS FILLING PRIMER Technical Data Sheet No 101 General Technical Description 2K Acrylic system sanding primer Excellent filling properties Excellent mechanical properties Easy to sand VOC compliant with the regulations Mix 3 parts P 333 PRIMER with 1 part H 725 HARDENER FOR PRIMERS Thinner addition 10 - 15% 740 ACRYL NORMAL or 741 ACRYL SLOW THINNER/ REDUCER On old, sanded paint work OEM surfaces Thermoplastic Coatings - TPA Fiberglass Clean and sanded steel panels Pretreatment / Cleaning of substrate Clean substrate using a soft cloth and 770 ANTISIL NORMAL / 771 ANTISIL FAST DEGREASER Make sure the surface is first wiped dry and then air dried HB Body Polyester Fillers HB Body Wash Primer P961 Etch Primer Make sure you always use appropriate face protection and good ventilation Product Application: As a HS sanding primer 2 passes »» Apply one coat, and after 10 min flash off time apply the second full coat. 3:1 mix with H 725 HARDENER FOR PRIMERS Pot life: 60 min @23°C (73°F) Addition 10-15% of thinner / reducer. Use 740 ACRYL NORMAL or 741 ACRYL SLOW THINNER / REDUCER Ready to spray: 22 - 24 s DIN 4 @ 20°C (68°F) Compliant Spray gun 1.5 – 1.8 mm 2 - 2.5 bar (29 - 36 psi) inlet pressure 2x coats = 100-120 μm (3.9-4.7mil) HVLP Spray gun 1.5 – 1.7 mm 1.5 - 2 bar (22-29psi) inlet pressure 2x coats = 100-120 μm (3.9-4.7mil) 10 min / 23°C (73°F) Flash off time It can be painted over with HB BODY Color Solutions Basecoat Mix System HB BODY Color Solutions 2K Acrylic Mix System HB BODY Color Solutions Aquabase Mix SystemAlways wear protective equipment Follow the application instructions mentioned in this TDS 2K paint systems tend to react with water, hence all the equipment used must be moisture free. Isocyanates may cause skin sensitization. More specifically, care should be taken when handling the material. Anyone with a history of histaminic conditions, or respiratory problems should consult the doctor first. For professional use only. The information displayed on this sheet has been carefully selected through a series of laboratory investigations. It is based on our best knowledge at the time of issue. The data is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check for newer updates or further information if needed for his intended purpose. The intellectual property of this product, trademarks and copyrights is protected. All rights reserved. The relevant Material Safety Data Sheet and warnings displayed on the label must be read carefully. We may modify and / or discontinue operation of all or portions of this information at any time in our sole discretion, without any notice and assume no responsibility to update the information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. HB BODY S.A. AUTO REFINISHING PRODUCTS, GREECE ww

P 333 3:1 HS FILLING PRIMER Technical Data Sheet No 101 Product Application: Applied direct on plastic bumpers (PE - PP - ABS - TSOP etc.) 1 - 2 passes »» Apply one coat, and after 10 min flash off time apply the second full coat. Dry sanding P 180 - P 220 (never with a scotch brite) Clean substrate using a soft cloth and 770 ANTISIL NORMAL / 771 ANTISIL FAST DEGREASER Make sure the surface is first wiped dry and then air dried Make sure you always use appropriate face protection and good ventilation 3:1 mix with H 725 HARDENER FOR PRIMERS Pot life: 60 min @23°C (73°F) Addition 50 - 60% of thinner...