P 261
1Pages

P 261 POLYESTER FILLING PRIMER Technical Data Sheet No 121 General Technical Description 2K polyester-based Spray Filling Primer Mix 100 parts P 261 POLYESTER FILLING PRIMER with 5 parts BODY HARDENER Most rough metallic surface areas Addition 0 - 5% BODY 780 polyester THINNER / REDUCER Easily applied by spray gun Easily sanded after 3-5 h at 23°C (73°F) , resulting in smooth non porous surface Pretreatment / Cleaning of substrate Suitable for filling of rough surface areas VOC compliant with the regulations Wooden surfaces Clean substrate using a soft cloth and 770 ANTISIL NORMAL /771 ANTISIL FAST DEGREASER Make sure the surface is first wiped dry and then air dried Make sure you always use appropriate face protection and good ventilation Product Application: As a HS Sanding Primer (Apply on metallic surfaces) 100:5 mix with BODY HARDENER Pot life: 45min @23°C (73°F) Addition 0 - 5% BODY 780 polyester thinner / reducer Ready to spray: 14 - 19 sec DIN 6 @ 20°C (68°F) Compliant spray gun: 2.5 mm 1.5 - 2 bar (22-29psi) inlet pressure 2x coats = 200-250μm (8-10mil) HVLP spray gun: 1.5 - 1.8 mm 1.5 - 2 bar (22-29psi) inlet pressure 3x coats = 200-250μm (8-10mil) 15 - 20 min / 23°C (73°F) Flash off time Short wave 6-10 min distance 60-70 cm P320 - P400 Flat bed sander P 600 – P 800 Sanding by hand, wet It can be painted over with HB BODY Color Solutions Basecoat Mix System HB BODY Color Solutions 2K Acrylic Mix System HB BODY Color Solutions Aquabase Mix System Always wear protective equipment Follow the application instructions mentioned in this TDS Flash Point: 31°C / 88°F Specific Gravity: 1.4 g/cm3 Solid Content (No thinner): 71% Weight VOC (2004/42/EC) This product is a special refinish product based on its ingredients and its properties. The maximum VOC content in this category is 540 g/L. The VOC content in the ready for use form of this product is 530 g/L. 2004/42/IIB(c)(540)530 Theoretical Coverage: Cleaning of equipment: Clean after final use with 740 ACRYL NORMAL THINNER / REDUCER Remarks: • Not recommended for spot panel repairs. • Application only with Body Hardener. Mix well with the filler. Do not add more than 5% as this may cause staining of the topcoat finish. •Avoid other thinners / reducers (e.g. NITRO THINNER). • Do not apply to Etch Primer, 1K Filler, TPA substrates and soft old paintwork. • Do not apply at temperatures below +5°C (40°F). • It can be used by countries that do not adopt the VOC legislation as well. Caution: Always check with a cloth and thinner if the panel is an OEM (E-COAT) panel. On OEM (E-COAT) panels, the cloth stays clean. Storage Shelf life: • Polyester materials have a limited shelf life. Store in a cool place (+5°C to 25°C) (40°F - 77°F) and use within 12 months for best results. Hardener paste contains organic peroxide and is an oxidant. If hardener comes in contact with the skin, wipe off immediately and wash with soap and water. After eye contact irrigate copiously with water and seek medical advice immediately. For professional use only. The information displayed on this sheet has been carefully selected through a series of laboratory investigations. It is based on our best knowledge at the time of issue. The data is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check for newer updates or further information if needed for his intended purpose. The intellectual property of this product, trademarks and copyrights is protected. All rights reserved. The relevant Material Safety Data Sheet and warnings displayed on the label must be read carefully. We may modify and / or discontinue operation of all or portions of this information at any time in our sole discretion, without any notice and assume no responsibility to update the information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. HB BODY S.A. AUTO REFINISHING PRODUCTS,