970 FILLSEALER Technical Data Sheet No 123 General Technical Description 2K Acrylic system fillsealer ideal for sanded areas and where putty was been applied Excellent as adhesion intermediator over non sanded old paints No need to sand it within 10-12 hours of the application. After 12 hours period it has to be sanded Mix 2 parts 970 FILLSEALER with 1 part H 729 HARDENER NORMAL Surface On old, non sanded paint work OEM surfaces Thermoplastic Coatings - TPA Thinner / Reducer addition 20%: • 740 ACRYL NORMAL or 741 ACRYL SLOW THINNER / REDUCER Clean and sanded steel panels HB Body Polyester Fillers Pretreatment / Cleaning of substrate Clean substrate using a soft cloth and 770 ANTISIL NORMAL / 771 ANTISIL FAST DEGREASER Make sure the surface is first wiped dry and then air dried Make sure you always use appropriate face protection and good ventilation VOC compliant with the regulations Product Application: Fillsealer Transparent Primer 2 passes »» Apply one coat, and after 15-20 min flash off time apply the second full coat. 2:1 mix with H 729 HARDENER FOR PRIMERS NORMAL Pot life: 2-3hrs @ 23°C (73ºF) Addition 20% of 740 ACRYL NORMAL or 741 ACRYL SLOW THINNER / REDUCER Ready to spray: 16-19s DIN 4 @ 20°C (68°F) Compliant Spray gun 1.5 – 1.8 mm 2 - 2.5 bar (29 - 36 psi) inlet pressure 2x coats = 40-50μm (1.6-2mil) HVLP 1.5 – 1.7 mm 1.5 - 2 bar (22-29psi) 2x coats = 40-50μm (1.6-2mil) 15 -20min / 23°C (73ºF) Flash off time 10-12h / 23°C (73°F) 20-30 min / 60°C (140°F) panel temperature Short wave 8 – 12 min distance 60-70cm It can be painted over with HB BODY Color Solutions Basecoat Mix System HB BODY Color Solutions 2K Acrylic Mix System HB BODY Color Solutions Aquabase Mix System Always wear protective equipment Follow the application instructions mentioned in this TDS Flash Point: 28°C / 82°F Specific Gravity: 1.30 g/cm3 Solid Content (No thinner): 75% Weight VOC (2004/42/EC) This is a special refinish product based on its ingredients and its properties. The maximum VOC content in this category is 540 g/L. The VOC content in the ready for use form of this product is 540 g/L. 2004/42/IIB(c)(540)540 Theoretical Coverage: 6 m2 / l at 50 micron (2mil) dry film thickness Remarks: • Allow for additional time for combi spray booths to reach the desired temperature • Application only with the recommended hardeners and thinners / reducers • It can be used by countries that do not adopt the VOC legislation as well. • Do not use at temperatures below 15°C (59°F) Storage Shelf life: • Store in a cool place (+5°C to 25°C) (41°F - 77°F) and use within 12 months for best results. Guaranteed shelf life of 24 months in unused original containers. Cleaning of equipment: Clean after final use with 740 ACRYL NORMAL THINNER / REDUCER 2K paint systems tend to react with water, hence all the equipment used must be moisture free. Isocyanates may cause skin sensitization. More specifically, care should be taken when handling the material. Anyone with a history of histaminic conditions, or respiratory problems should consult the doctor first. For professional use only. The information displayed on this sheet has been carefully selected through a series of laboratory investigations. It is based on our best knowledge at the time of issue. The data is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check for newer updates or further information if needed for his intended purpose. The intellectual property of this product, trademarks and copyrights is protected. All rights reserved. The relevant Material Safety Data Sheet and warnings displayed on the label must be read carefully. We may modify and / or discontinue operation of all or portions of this information at any time in our sole discretion, without any notice and assume no responsibility to update the information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. HB BODY S.A. AUTO REFINISHING PRODUCTS