BA
1 / 45Pages

Valve bank (nominal size 6) type BA Product documentation Operating pressure pmax: Flow rate Qmax:

© by HAWE Hydraulik SE. The reproduction and distribution of this document as well as the use and communication of its contents to others without explicit authorization is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of patent or utility model applications. Brand names, product names and trademarks are not specifically indicated. In particular with regard to registered and protected names and trademarks, usage is subject to legal provisions. HAWE Hydraulik respects these legal provisions in all cases. HAWE Hydraulik cannot provide...

Overview of valve bank (nominal size 6) type BA A valve bank combines different valves for operating independent consumers. The directional valve bank type BA consists of several valve sections, which are based on sub-plates. They can be used to exibly assemble compact hydraulic manifolds. The type BA valve bank can be ange mounted directly on the hydraulic power packs. The intermediate plates type NZP enable additional functions and contain, for example, pressure reducing valves, shock valves, load-holding valves, etc. An intermediate plate can be inserted between the sub-plate and the...

Available versions -G 24 2.6 "Solenoid voltage and connector" 2.5 "End plates" 2.3.2 "Sub-plates" 2.3 "Valve sections" 2.4 "Intermediate plates" 2.2 "Connection block" 2.1 "Basic type and size" 2.1 Basic type and size Type Flow rate Qmax (lpm) for directional valves NG 6 (ISO 4401-03, CETOP 03) and others Return line pressure pmax (bar) DAMAGE Observe the specifications of the attached directional valves and upstream hydraulic power packs. 2.2 Connection block Coding Without coding Direct mounting on connection blocks of type AB (D 6905 AB) for combination with compact hydraulic power packs...

2.3 Valve sections 2.3.1 Directional valves Coding Flow rate Qmax (lpm) 3/2, 3/3, 4/2 and 4/3 directional spool valve with additional options (pressure monitoring, restrictors and restrictor check valves in the ports) 3/3 and 4/3 directional spool valve Clamping module (combination of 4/2 or 4/3 directional spool 25 valve, pressure reducing valve and tracked pressure switch) 2/2, 3/2 and 4/3 directional seated valves Directional valves NG 6 Can be combined with intermediate plates type NZP to D 7788 Z NSWP 2 NOTE 20 In contrast to the designation of a single valve to D 7765 N, a coding for...

Circuit examples for directional valves sub-plates NSWP 2 G/M/R/ABV1.0 BBV1.5/70/S/3

Series (See coding for double sub-plates for two individual sections /10) Position of the consumer ports on opposite side additional, releasable check valve in A (Type CRH 1 to D 7712) with additional throttle in T (Type Q 30 to D 7730) additional pressure gauge connections MA and MB (See coding for double sub-plates for two individual sections /10) additional drain port for the combination with the intermediate plate NZP 16 SDM 2L to D 7788 Z G 3/8 NOTE following valve sections must also have sub-plate coding /4. For the end plate, coding -1L to Chapter 2.5, "End plates", is selected. /5...

2.4 Intermediate plates Coding Pressure reducing valve for pressure reduction in the downstream P channel see Chapter 2.4.1, "Pressure reducing valves in the P channel" Intermediate plate as spacer (50 mm) without internal function Intermediate plate with additional P and R ports ZPL/V... ZPL/S... Intermediate plate for a 2nd Speed see Chapter 2.4.2, "Intermediate plate for a 2nd Speed" ZPL/MVE 6/.. ZPL/MVE 6/../R ZPL/MVEX 6/.. ZPL/MVEX 6/../R Intermediate plate with pressure-limiting valve, drain valve and accumulator port Intermediate plate with proportional pressure-limiting valve for a...

2.4.1 Pressure reducing valves in the P channel Ordering example BA 2 A5 Check valve Pressure setting (bar) Pressure adjustment Pressure range Pressure reducing valve Pressure reducing valve Coding Pressure reducing valve type CDK to D 7745 Pressure reducing valve type CDK to D 7745, valve turned through 90° Pressure reducing valve type CDK to D 7745, with direct accumulator port Pressure reducing valve type CLK to D 7745 L, with overpressure function Without pressure reducing valve with tapped plug prepared for retrotting

Check valve in P coding R Drain valve Check valve in P coding R Drain valve Check valve in P coding R Drain valve Coding -CZX, CZAX, CZDX, LZX (Example illustration as type CZX) Pressure range Coding Flow rate Qmax (lpm) Flow rate Qmax (lpm) Short model (not for type LZ) prepared, with tapped plug * not for type LZ ** Value in brackets dene the pressure stage

Pressure adjustment Coding Circuit symbol Without coding Fixed, tool adjustable Manually adjustable, with lock nut not directly combinable next to each other Turn knob, lockable not for type LZ Check valve Coding without check valve in P with check valve in P (not for type CZD) 2.4.2 Intermediate plate for a 2nd Speed Application: Optional switching to a second speed, for example for set-up mode or to vary the ow rate to traverse speed proles. Ordering example BA 2 A5 -G 24 2.4.3.1 "Solenoid voltage and solenoid male connector for proportional solenoid" Orice in the P channel...

Coding ZPL/SP Coding ZPL/S(PG)/PB... Coding ZPL/S(PG)/P Coding ZPL/VP Coding ZPL/V(PG)/PB... Coding ZPL/V(PG)/P Orice in the P channel Coding closed (not sealed for zero leakage) DAMAGE Not in combination with coding ZPL/VP and ZPL/SP.

2.4.3 Intermediate plate with proportional pressure-limiting valve for second pressure circuit in BA valve bank Application: Compact solution for two pressure circuits in one valve bank. DAMAGE Combination with a dual-circuit pump, for example type HK 4 to D 7600-4 and a connection block type Sk 6905 Z/AP is feasible. Circuit symbol Prop. pressure-limiting valve ZPL / P.. Example schematic plan Check valve at P (optional) max. pressure setting of pressure-limiting valve (bar) MVF 2.4.3.1 "Solenoid voltage and solenoid male connector for proportional solenoid" "Proportional pressure-limiting...