*mydirectindustry

Catalogs
Haskel
HGT-150/90

HGT-150/90

Product catalog summary

Specifications:
The H-Drive Booster Model HGT-150/90 is designed with a maximum gas inlet pressure of 1450 psi (100 Bar) and a minimum gas inlet pressure of 50 psi (3.5 Bar). The maximum gas outlet pressure is 10,000 psi (690 Bar), and the maximum hydraulic drive pressure is 3600 psi (250 Bar). The gas piston displacement is 329 cubic inches (5.39 liters). The maximum recommended compression ratio (CR) is 36:1.

Performance Chart:
The performance chart provides outlet flow rates in Nm³/hr (scfm) based on varying gas supply pressures. The chart is used to determine the required cycling speed by drawing horizontal and vertical lines representing the required outlet flow and available gas supply pressure, respectively.

Procedures and Recommendations:
- Vent to a controlled environment, not exceeding 50 psig back pressure.
- Remove plug upon installation and direct it to an oil catch tray.
- Torque tie rods to 410 ± 10 ft-lbs in 16 places, applying anti-seize compound to threads.
- Torque screws to 8 ± 0.5 ft-lbs, cooling connections to 50 ± 10 ft-lbs, hydraulic connections to 200 ± 10 ft-lbs, check valves tubes to 50 ± 10 ft-lbs, and vent connections to 50 ± 10 ft-lbs.
- Reverify all torque values after testing.
- Drain coolant through the specified port before shipping and during maintenance intervals, torquing the plug no more than 25 ft-lbs.
- Touch up hydraulic cylinder paint before shipping using black paint RAL 9005.
- Engage only one screw through the bracket on each gas section.
- Plug all open ports with plastic caps before shipping.

Parts List:
The document includes a detailed parts list with quantities and descriptions, such as hydraulic cylinder assembly, gas section assembly, inlet and outlet check valve assemblies, washers, nuts, retainer caps, O-rings, and screws.

Notes:
- Materials include stainless steel metallic body, spring-activated seals, rubber O-rings, and coated steel fasteners and washers.
- For full operating parameters, contact the factory or distributor with specific data including gas supply pressure, gas outlet pressure, required outlet flow, gas being transferred, and application details.

Catalog excerpts

: STAINLESS STEEL METALIC BODY, SPRING ACTIVATED SEALS, RUBBER O-RINGS, TEEL FASTENERS AND WASHERS 2 FOR GENERAL ARRANGEMENT DIMENSIONS CONTROLLED ENVIRONMENT. NOT TO EXCEED 50 PSIG BACK PRESSURE LUG UPON INSTALLATION & DIRECT IT TO AN OIL CATCH TRAY OF WASHERS TO FACE THE NUTS H-Drive Booster Model HGT-150/90 10 FT-LBS, 16 PLACES. APPLY ANTI-SEIZE COMPOUND TO THREADS LEAST 3 THREADS OUT OF THE NUTS ON EACH SIDE. TIGHTEN IN 100 FT-LBS INCREMENTS OOLING CONNECTIONS TO 50±10 FT-LBS YDRAULIC CONNECTIONS TO 200±10 FT-LBS Max Hydraulic Drive Pressure Psi g 3600 HECK VALVES TUBES TO 50±10 FT-LBS ALL TORQUE VALUES AFTER TESTING To determine required cycling speed: Parts List 1. Draw horizontal line representing ITEM HGT-150/90-1-0 HGT-150/90-2-0 DESCRIPTION QTY required 150MM BORE, 1 88062 88062 1 HYD CYLINDER ASSY, outlet flow 12" STROKE, 3800 PSI 2 88095 88095-2 GAS SECTION ASSY, 150MM, 12" STROKE, H-DRIVE 1 2. Draw vertical line representing the gas supply pressure available 3 88096 88096-2 - 20 CPM GAS SECTION ASSY, 90MM, 12" STROKE, H-DRIVE 1 Qo 4 88116 88116-2 2 INLET CHECK VALVE ASSY, HDGB will give the 3. Where both lines cross 5 88117 88117-2 CHECK VALVE ASSY,cycling speed of the H-Drive 2 approx. OUTLET, H-DRIVE 6 88125 88125 LABEL, TORQUE operating parameters of H-Drive INSTRUCTIONS, H-DRIVE 2 For full 7 88137 88137 - 15 CPM LABEL, NAME PLATE, H-DRIVE conditions including 1 Qo running at particular the hydraulic power supply required, contact 11 CNF00383 16 CNF00383 WASHER, HYTORC, STEEL, BLACK OXIDE, 24MM BOLT factory or distributor with M24X3, 19MM LONG 12 CNF00384 CNF00384 NUT, STEEL, GRADE 8, ZINC PLATE, following data: 16 14 86579 86579 RETAINER CAP Gas supply pressure 2 • Ps 15 568018-9 568018-9 - 10 CPMO-RING • Po Gas outlet pressure 2 Qo 16 CNF00385 4 CNF00385 SCREW,SOCK HEAD 1/4-20X7/8 • Qo Outlet flow required THIS DRAWING EMBODIES A NEXT ASSY (REF ONLY) Haskel International, LLC OLANT THROUGH THIS PORT BEFORE SHIPPING & FOR MAINTENANCE INTERVALS Minimum Gas inlet : 3.5 Bar g (50 psig) Maximum Gas Inlet : HYDRAULIC CYLINDER PAINT BEFORE SHIPPING. USE BLACK PAINT RAL 9005.100 Bar g (1450 psig) Maximum Gas Outlet : 690 Bar g (10,000 psig) 500 AS SECTION, ONLY ENGAGE ONE SCREW THRU THE BRACKET. Maximum Recommended CR : 36:1 (295) Outlet Flow Nm3/hr (scfm) HE PLUG NO MORE THAN 25 FT-LBS OPEN PORTS WITH PLASTIC CAPS BEFORE SHIPPIN CONFIDENTIAL PROPRIETARY DESIGN, ALL RIGHTS FOR REPRODUCTION, MANUFACTURING OR PATENTS ARE RESERVED BY HASKEL INTERNATIONAL, LLC. INFORMATION CONTAINED HEREIN IS SUBJECT TO THE EXPORT ADMINISTRATION REGULATIONS (EAR) OF THE UNITED STATES OF AMERICA AND EXPORT CLASSIFIED UNDER THOSE REGULATIONS AS (ECCN: EAR99). NO PORTION OF THIS DOCUMENT CAN BE RE-EXPORTED FROM THE RECIPIENT COUNTRY OR RE-TRANSFERRED OR DISCLOSED TO ANY OTHER ENTITY OR PERSON NOT AUTHORIZED TO RECEIVE IT WITHOUT THE PRIOR AUTHORIZATION OF HASKEL INTERNATIONAL, LLC. THIS NOTICE SHALL BE ATTACHED TO ANY REPRODUCED SECTION OF THIS DOCUMENT. Gas Supply Pressure Bar g (psig) MACHINE FINISH 125 [3.2] TOLERANCES ARE: DECIMALS: FRACTIONS: ANGLES: GAS BOOSTER, H-DRIVE, 12" STROKE, HGT-150/90 88122-TAB 81400 THIRD ANGLE PROJECTION CAGE CODE INVENTOR DRAWING

Open the catalog to page 1

HGT-150/90

HGT-150/90

Catalog excerpts

All Haskel catalogs and technical brochures

Archived catalogs