*mydirectindustry

Catalogs
Haskel
HGT-150/63

HGT-150/63

Product catalog summary

Specifications:
The H-Drive Booster Model HGT-150/63 is designed with a maximum gas inlet pressure of 580 psi (40 bar) and a minimum gas inlet pressure of 50 psi (3.5 bar). The maximum gas outlet pressure is 15,000 psi (1034 bar), with a maximum recommended compression ratio (CR) of 36:1. The maximum hydraulic drive pressure is 3600 psi (250 bar), and the gas piston displacement is 329 cubic inches (5.39 liters).

Performance Chart:
The performance chart provides outlet flow rates in Nm³/hr (scfm) based on varying gas supply pressures. The chart is used to determine the required cycling speed by drawing horizontal and vertical lines representing the required outlet flow and available gas supply pressure, respectively.

Procedures and Recommendations:
- Vent to a controlled environment, not exceeding 50 psig back pressure.
- Remove plug upon installation and direct it to an oil catch tray.
- Use specific seal kits for gas sections and hydraulic cylinders.
- Torque specifications are provided for various components, including tie rods, screws, cooling connections, hydraulic connections, check valve tubes, and vent connections.
- Reverify all torque values after testing.
- Drain coolant through the specified port before shipping and during maintenance intervals.
- Touch up hydraulic cylinder paint before shipping using black paint RAL 9005.
- Engage only one screw through the bracket on each gas section.
- Plug all open ports with plastic caps before shipping.

Parts List:
The document includes a detailed parts list with quantities and descriptions for components such as hydraulic cylinder assemblies, gas section assemblies, check valve assemblies, washers, nuts, retainer caps, O-rings, and screws.

Notes:
- Materials include stainless steel metallic bodies, spring-activated seals, rubber O-rings, and coated steel fasteners and washers.
- General arrangement dimensions are provided on sheet 2.
- For full operating parameters, contact the factory or distributor with specific data including gas supply pressure, gas outlet pressure, required outlet flow, gas being transferred, and application details.

Catalog excerpts

S: STAINLESS STEEL METALIC BODY, SPRING ACTIVATED SEALS, RUBBER O-RINGS, STEEL FASTENERS AND WASHERS ET 2 FOR GENERAL ARRANGEMENT DIMENSIONS A CONTROLLED ENVIRONMENT. NOT TO EXCEED 50 PSIG BACK PRESSURE PLUG UPON INSTALLATION & DIRECT IT TO AN OIL CATCH TRAY E OF WASHERS TO FACE THE NUTS H-Drive Booster Model HGT-150/63 10 FT-LBS, 16 PLACES. APPLY ANTI-SEIZE COMPOUND TO THREADS T LEAST 3 THREADS OUT OF THE NUTS ON EACH SIDE. TIGHTEN IN 100 FT-LBS INCREMENTS COOLING CONNECTIONS TO 50±10 FT-LBS HYDRAULIC CONNECTIONS TO 200±10 FT-LBS Max Hydraulic Drive Pressure CHECK VALVES TUBES TO 50±10 FT-LBS VENT CONNECTIONS TO 50±10 FT-LBS Y ALL TORQUE VALUES AFTER TESTING To determine required cycling speed: OOLANT THROUGH THIS PORT BEFORE SHIPPING & FOR MAINTENANCE INTERVALS 250 1. Draw horizontal line representing required outlet flow Parts List 2. Draw vertical line representing the gas ITEM HGT-150/63-1-0 HGT-150/63-2-0 DESCRIPTION QTY supply pressure available 1 88062 88062 Qo - 20 HYD CYLINDER ASSY, 150MM BORE, 12" STROKE, 3800 PSI 1 2 88095 88095-2 CPM GAS SECTION ASSY, 150MM, 12" STROKE, H-DRIVE 1 3. Where both lines cross will give the 3 88097 88097-2 GAS SECTION ASSY, 63MM, 12" STROKE, H-DRIVE 1 approx. cycling speed of the H-Drive 4 88116 88116-2 INLET CHECK VALVE ASSY, HDGB 2 5 88117 CHECK For full ASSY, OUTLET, H-DRIVE H-Drive VALVE operating parameters of 2 88117-2 Qo - 15 6 88125 88125 2 LABEL, TORQUEat particular conditions including running INSTRUCTIONS, H-DRIVE 7 88137 88137 CPM LABEL, NAME PLATE, power supply required, contact 1 the hydraulic H-DRIVE 11 CNF00383 16 CNF00383 WASHER, HYTORC, STEEL, BLACK following data: factory or distributor with OXIDE, 24MM BOLT 12 CNF00384 16 CNF00384 NUT, STEEL, GRADE 8, ZINC PLATE, M24X3, 19MM LONG • Ps Gas 14 86579 2 RETAINER CAP supply pressure Qo - 10 15 568018-9 2 O-RING • Po Gas outlet pressure CPM 16 CNF00385 4 SCREW,SOCK HEAD 1/4-20X7/8 THIS DRAWING EMBODIES A • Qo Outlet flow required NEXT ASSY (REF ONLY) Haskel International, LLC P HYDRAULIC CYLINDER PAINT BEFORE SHIPPING. USE BLACK PAINT RAL 9005. Outlet Flow Nm3/hr (scfm) Minimum Gas inlet : 3.5 Bar g (50 psig) Inlet : 40 Bar g (580 psig) (118) Maximum Gas Outlet : 1034 Bar g (15,000 psig) OPEN PORTS WITH PLASTIC CAPS BEFORE SHIPPING Maximum Recommended CR : 36:1 GAS SECTION, ONLY ENGAGE ONE SCREW THRU THE BRACKET. Maximum Gas CONFIDENTIAL PROPRIETARY DESIGN, ALL RIGHTS FOR REPRODUCTION, MANUFACTURING OR PATENTS ARE RESERVED BY HASKEL INTERNATIONAL, LLC. INFORMATION CONTAINED HEREIN IS SUBJECT TO THE EXPORT ADMINISTRATION REGULATIONS (EAR) OF THE UNITED STATES OF AMERICA AND EXPORT CLASSIFIED UNDER THOSE REGULATIONS AS (ECCN: EAR99). NO PORTION OF THIS DOCUMENT CAN BE RE-EXPORTED FROM THE RECIPIENT COUNTRY OR RE-TRANSFERRED OR DISCLOSED TO ANY OTHER ENTITY OR PERSON NOT AUTHORIZED TO RECEIVE IT WITHOUT THE PRIOR AUTHORIZATION OF HASKEL INTERNATIONAL, LLC. THIS NOTICE SHALL BE ATTACHED TO ANY REPRODUCED SECTION OF THIS DOCUMENT. Gas Supply Pressure Bar g (psig) FRACTIONS: ANGLES: GAS BOOSTER, H-DRIVE, 12" STROKE, HGT-150/63 88123-TAB 81400 THIRD ANGLE PROJECTION CAGE CODE INVENTOR DRAWING

Open the catalog to page 1

VENT PORT 3/4" SAE/JIC

Open the catalog to page 2

HGT-150/63

HGT-150/63

Catalog excerpts

All Haskel catalogs and technical brochures

Archived catalogs