T 2 FOR GENERAL ARRANGEMENT DIMENSIONS A CONTROLLED ENVIRONMENT. NOT TO EXCEED 50 PSIG BACK PRESSURE PLUG UPON INSTALLATION & DIRECT IT TO AN OIL CATCH TRAY E OF WASHERS TO FACE THE NUTS TIE RODS TO 410 10 FT-LBS, 16 PLACES. APPLY ANTI-SEIZE COMPOUND TO THREADS LEAST 3 THREADS OUT OF THE NUTS ON EACH SIDE. TIGHTEN IN 100 FT-LBS INCREMENTS PROX SWITCH PLUGS TO 65 5 FT-LBS. MAKE METAL TO METAL CONTACT. EXTRUSION ALLOWED H-Drive Booster Model HGD-63 COOLING CONNECTIONS TO 50±10 FT-LBS HYDRAULIC CONNECTIONS TO 200±10 FT-LBS CHECK VALVES TUBES TO 50±10 FT-LBS VENT CONNECTIONS TO 50±10 FT-LBS 15000 Max Hydraulic Drive Pressure ALL TORQUE VALUES AFTER TESTING OOLANT THROUGH THIS PORT BEFORE SHIPPING & FOR MAINTENANCE INTERVALS THE PLUG NO MORE THAN 30±5 FT-LBS P HYDRAULIC CYLINDER PAINT BEFORE SHIPPING. USE BLACK PAINT RAL 9005. (706) GAS SECTION, ONLY ENGAGE ONE SCREW THRU THE BRACKET. OPEN PORTS WITH PLASTIC CAPS BEFORE SHIPPING Minimum Gas inlet : 7 Bar g (100 psig) Maximum Gas Inlet : 1034 bar g (15,000 psig) Maximum Gas Outlet : 1034 Bar g (15,000 psig) Maximum Recommended CR : 6:1 Outlet Flow Nm3/hr (scfm) THIS DRAWING EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN, ALL RIGHTS FOR REPRODUCTION, MANUFACTURING OR PATENTS ARE RESERVED BY HASKEL INTERNATIONAL, LLC. INFORMATION CONTAINED HEREIN IS SUBJECT TO THE EXPORT ADMINISTRATION REGULATIONS (EAR) OF THE UNITED STATES OF AMERICA AND EXPORT CLASSIFIED UNDER THOSE REGULATIONS AS (ECCN: EAR99). NO PORTION OF THIS DOCUMENT CAN BE RE-EXPORTED FROM THE RECIPIENT COUNTRY OR RE-TRANSFERRED OR DISCLOSED TO ANY OTHER ENTITY OR PERSON NOT AUTHORIZED TO RECEIVE IT WITHOUT THE PRIOR AUTHORIZATION OF HASKEL INTERNATIONAL, LLC. THIS NOTICE SHALL BE ATTACHED TO ANY REPRODUCED SECTION OF THIS DOCUMENT. UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES [MM] DO NOT SCALE DRAWING REMOVE BURRS MACHINE FINISH 125 [3.2] TOLERANCES ARE: Gas Supply Pressure Bar g (psig) Haskel International, LLC Burbank, California 91502 GAS BOOSTER, H-DRIVE, 12" STROKE, HGD-63 • Qo Outlet flow required 88094-TAB_MARKETIN D 81400 DATE • Po Gas outlet pressure DRAWN PM 9/27/2016 CAGE CODE CAD being 88094 • GasFILENAME transferred NONE SCALE: NEXT ASSY (REF ONLY) THIRD ANGLE PROJECTION To determine required cycling speed: Parts List DESCRIPTION 1. Draw horizontal line representing HYD CYLINDER ASSY, 150MM BORE, 12" STROKE, 3800 PSI required outlet flow GAS SECTION ASSY, 63MM, 12" STROKE, H-DRIVE 2. Draw vertical line representing the gas INLET CHECK VALVE ASSY, HDGB CHECK VALVE ASSY, OUTLET, H-DRIVE supply pressure available LABEL, TORQUE INSTRUCTIONS, H-DRIVE 3. Where both lines cross will give the LABEL, NAME PLATE, H-DRIVE approx. cycling speed of the H-Drive SOCKET CAP SCREW WASHER, 5/8" BOLT, 1.312parameters of H-Drive For full operating OD, STEEL, ZINC PLATED WASHER, PRESSURE SEAL conditions including running at particular WASHER, HYTORC, STEEL, BLACK OXIDE, 24MM BOLT the hydraulic power supply required, contact NUT, STEEL, GRADE 8, ZINC PLATE, M24X3, 19MM LONG factory or distributor with following data: