*mydirectindustry

PVX 10160

Product catalog summary

Overview: The PVX 10160 is a variable displacement, axial piston, swash plate design pump suitable for both industrial and mobile applications. It operates with continuous pressures from 500 to 3750 psi and shaft speeds up to 2000 rpm.

Features:

Standard SAE ‘C’ 2- & 4-bolt mount.
Compact design with a rugged ductile iron frame.
Various porting configurations and drive shaft options.
Service-friendly with Viton shaft seal and O-rings.
Adjustable maximum and minimum volume stops.

Specifications:

Rated pressure: 3850 lb/in² (265 bar), Peak pressure: 4500 lb/in² (310 bar), Minimum pressure: 500 lb/in² (34 bar).
Theoretical flow at 1800 rpm: 74.0 gal/min (280.0 l/min).
Output torque at rated pressure: 6,128 in-lb (690.0 N-m).
Operating viscosities for petroleum-based fluids: 60 to 5000 SUS.
Filtration: Minimum 10 micron (abs.) required, ISO 16/13 cleanliness level.
Inlet conditions: Max temperature 140º F, resistance < 6 in. Hg (3 psi).
Case drain: Two ports, back-pressure < 25 psi.
Weight: Approximately 160 lbs.

Performance Data: Performance data obtained using ISO 32 Oil at 115° F shows volumetric efficiency and output flow at various pressures and shaft speeds.

Additional Information: Tandem pumps can be configured with side-ported models by adding a thru-drive shaft and coupling. Consult the factory for specific configurations and higher inlet temperature conditions.

Catalog excerpts

604 Progress Dr., Hartland, WI 53029 USA Tel: (262) 367-4299 Fax: (262) 367-5645 Email: [email protected] FRAME 3 PVX 10160 (160 cm.³/rev.) (10.0 in.³/rev.) VARIABLE DISPLACEMENT, AXIAL PISTON, SWASH PLATE DESIGN PUMP Features: Offered with a standard SAE ‘C’ 2- & 4-bolt mount. Incorporated in a compact design with rugged ductile iron frame. Offered with variety of porting configurations. Offered with a variety of drive shaft options. Is Service friendly. Equipped with Viton shaft seal and O-rings. Can be fitted with a variety of control options. Equipped with maximum and minimum volume stops. The latter is adjustable. This versatile PVX pump is aimed at operating in both industrial and mobile applications. With its continuous operating pressures ranging from 500 to 3750 psi, and shaft speeds up to 2000 rpm at atmospheric inlet conditions, this pump is designed for a long and dependable service.

Open the catalog to page 1

Input-shaft torque may not exceed the total of front-pump torque and (if added) rear-mounted units. A Consult Factory MODEL SPECIFICATION CHART CS - SAE C SPLINE CK - SAE C KEYED CC - SAE CC SPLINE KC - SAE CC KEYED REAR COUPLING AS - SAE A SPLINE AK-SAEA KEYED AB - SAE AB SPLINE BA - SAE AB KEYED BS - SAE B SPLINE BK-SAEBKEYED BB - SAE BB SPLINE KB - SAE BB KEYED CS - SAE C SPLINE" CK-SAEC KEYED" REAR FLANGE ROTATION / PORTS 18 CW / REAR PORT 19 CCW / REAR PORT 20 CW / SIDE PORT 21 CCW / SIDE PORT y SPECIAL FEATURES V - SPECIAL" W - WATER BASE STACK CONTROLS FL - FIXED FLOW-LOAD SENSOR AL -...

Open the catalog to page 2

Performance Data Obtained Using ISO 32 Oil @ 115° F Output Flow (gpm) Output Horsepower (HP) Volumetric Efficiency (%) Operating Viscosities: For petroleum-based fluids the optimal level is 150 SUS. For continuous operations, the level should range from 60 to 5000 SUS. Filtration: A minimum of 10 micron (abs.) filtration is required. A return line filter is preferred. Bypass filtration and suction filters/strainers are not recommended. Fluid cleanliness should conform to ISO 16/13 level. Inlet Conditions and Piping: The maximum temperature at the inlet should be 140º F. For higher levels consult...

Open the catalog to page 3