Catalog excerpts
Harrison Silverdale Ltd Unit 1 Traso Business Park. Callywhite Lane. Dronfield, Sheffield, S18 2XR Tel: 01246 296 930 • Fax: 01246 296 940 Email: fasteners@harrisonsilverdale.co.uk Internet: http:/fwww.harrisonsilverdale.co.uk Polyplast 30 Hex Head Part No. Substitute the length for the L In the part no. to specify the exact part required. The 30 deg. Flank angle and recessed core diameter of these thread forming screws for plastic have been developed following theoretical appraisal, exhaustive calculations and final proof testing. The 30 deg. Flank angle produces low radial forces when engaging the plastic, therefore resulting in less radial stresses and tension. In other words the hoop stresses in the plastic bosses are less than those experienced with conventional screws. The recessed core geometry provides the ideal flow director for the displaced plastic, encouraging a uniform flow to fill the pitch of the screw without material jamming. This results in the maximum amount of plastic being engaged to provide higher sheer loads, due to the increased bearing depth of the thread. A combination of the above and the ease of penetration of the 30 deg. Flank angle through the material and the way in which the plastic flows, reduces the torque required to drive the screw in. This fact therefore increases the margin between drive torque and stripping torque which of course minimises the potential of stripping during installation. The optimum pitch and maximum fill features provided by the recessed core results in a large area of plastic to be sheered prior to screw failure in tension. This creates a high resistance to pullout loads. All information is given for guidance only and designers should satisfy themselves as to the suitability of the specification by requesting samples
Open the catalog to page 1All Harrison Silverdale catalogs and technical brochures
-
Series: 20130 Type: D
1 Pages
-
Series 50505 Type: AN
1 Pages
-
Series: 20210 Type: 1411
2 Pages
-
Series: 40501 Type: EC3
2 Pages
-
Series: 40502 Type: ECS
1 Pages
-
Series: 40503 Type: D
1 Pages
-
Series: 40504 Type: CEC
2 Pages
-
Series: 40112 Type: CNSS
4 Pages
-
Series: 20110 Type: SF
1 Pages
-
Series: 20110 Type: FV
1 Pages
-
Series: 20133 Type: TRB
1 Pages
-
Series: 20105 Type: SC
2 Pages
-
Series: 20130 Type: DPW
1 Pages
-
Series: 20131 Type: E
1 Pages
-
Series: 20130 Type: D
1 Pages
-
Series: 20117 Type: HPI
1 Pages
-
Series: 20108 Type: HL
1 Pages
-
Series: 20106 Type: ISS
1 Pages
-
Series: 20106 Type: HIS
1 Pages
-
Series: 20103 Type: THC
1 Pages
-
Series 20108 Type: HL
1 Pages
-
Series 20106 Type: HSS
1 Pages
-
Series 20106 Type: ISS
1 Pages
-
Series 20106 Type: HIS
1 Pages
-
Series 20103 Type: TH
1 Pages
-
Series 40114 Type: CNUT
1 Pages
-
Series 20106 Type: IS
1 Pages
-
Series 50211 Type: TB2
1 Pages
-
Series 50211 Type: TB1
1 Pages
-
Series 50201 Type: CT
2 Pages
-
Series 20210 Type: 1413
1 Pages
-
Series 20210 Type: 1412
1 Pages
-
Series 20210 Type: 1411
1 Pages
-
Series 30314 Type: COM
2 Pages
-
Series 30307 Type: FL
2 Pages
-
Series 30304 Type: FN
1 Pages
-
Series 30302 Type: CN
3 Pages
-
Series 30312 Type: CS
2 Pages
-
Series 40201 Type: SL
1 Pages
-
Series 40111 Type: CN
3 Pages
-
Series 40112 Type: CNSS
4 Pages
-
Series 20103 Type: THC
1 Pages
-
20103 Type: TH
1 Pages
-
30261 TF
2 Pages
-
30260 TPLB
2 Pages
-
30260 TPB
2 Pages
-
30260 TPL
2 Pages
-
30260 TP
2 Pages
-
FASTENERS FOR PLASTIC CATALOGUE
32 Pages
Archived catalogs
-
Specialised Fasteners
67 Pages