描校 棱边去除毛刺，未注棱边、孔口倒角C0.2； 注意气路孔道联通； 2 旧底图总号 注意螺孔深度，不要打穿气路孔道； Another option for gripping square products 表面光洁美观，无划痕、磕伤、局部变形等缺陷； 表面硬质氧化，层厚0.035-0.040mm。 底图总号 For the gripping of square products with centering 1 6.187 比例 4 工艺 校核 Structural Design of T-shaped Guide Rail 主管设计 审核 日期 With the classic T-shaped guide rail structure, the hard 替代 共 1 张 第 1 张 版本 批准 rail surface has excellent bearing 标记 capacity 处数 分区 更改文件号 签名 年 月 4 3 标准化 设计 requirements, TF series is another preferred solution 2 other than FR. Pusher module (optional) Inductive proximity sensor(optional) Gripper body Wedge drive mode Thanks to excellent drive structure, it has the characteristics of high load and high centering accuracy Anodized aviation aluminum housing By adopting the high-quality aviation aluminum housing, the gripper is ensured to have the characteristics of high load while minimizing the weight. 1.6 TF powerful four-finger gripper series The pneumatic four-finger centering gripper, with the T-shaped load-bearing structure, supports different

Closed Open Cylinder bore Maximum shell diameter Four-finger gripper Without push plate 3 Mounting hole of gripping finger High temperature resistance 底图总号 2 Gripping finger positioning groove Gripper mounting hole 4 工艺 A 4 Compressed airB connection port 审核 *Two sensors are required for each gripper. For the detailed monitoring of two positions, see the sensor appendix. Gripper mounting 标准化and positioning B Location of inductive proximity sensor hole/grease injection hole D Bottom ventilation hole (version-B) Inductive proximity sensor Gripping finger location pin bushing (standard) Gripping...

End-of-Arm Tooling Gripping force curve Static load-bearing torque 比例 3 Parallel gripper long stroke series4 FOUK-TF Cylinder bore Maximum shell diameter Four-finger gripper High temperature resistance Without push plate 2 Gripping finger positioning groove Gripper mounting hole Gripper mounting and positioning hole/grease injection hole D Bottom ventilation hole (version-B) A Compressed air connection port 4 B Location of4inductive proximity sensor *Two sensors are required for each gripper. For the detailed monitoring of two positions, see the sensor appendix. 更改文件号 签名hole 年of 月gripping 日 3...

End-of-Arm Tooling Maximum shell diameter Four-finger gripper Gripper mounting hole Gripper mounting and positioning Opening/closing time Gas consumption of single opening and closing cycle P: Compressed air pressure [bar] Gas consumption: volume of gas consumed at normal pressure (0.5MPa) Connecting plate 1 Repeated gripping accuracy/mm Operating air pressure range/bar Temperature range of application/°C Maximum allowable single-finger gripping weight/kg Specification of air connection port Workpiece weight The length A of the push rod can be of the standard version or the extended version,...

End-of-Arm Tooling Parallel gripper long stroke series FOUK-TF distance/mm 借(通)用件登记 160 Gripping Cylinder bore Maximum shell diameter Four-finger gripper Without push plate *Two sensors are required for each gripper. For the detailed monitoring of two positions, see the sensor appendix. 棱边去除毛刺，未注棱边、孔口倒角C0.2； 注意气路孔道联通； Closed B 注意螺孔深度，不要打穿气路孔道； 2-M3 零件代号 表面光洁美观，无划痕、磕伤、局部变形等缺陷； 表面硬质氧化，层厚0.035-0.040mm。 2 Gripping finger positioning groove Gripper mounting hole 4 positioning Gripper mounting and Compressed air connection port A设计 标准化 工艺 sensor Location of inductive proximity B校核 B 主管设计 审核 C Positive-pressure...

Parallel gripper long stroke series FOUK-TF其余 End-of-Arm Tooling 杭州弗克机械科技有限公司 Serial No. Cylinder bore 21 Maximum shell diameter Four-finger gripper 描校rod Length of push C40 C50 1/ Workpiece weight Gas consumption of single opening and closing cycle Repeated gripping accuracy/mm Operating air pressure range/bar Temperature range of application/°C Maximum allowable single-finger gripping weight/kg Specification of air connection port P: Compressed air pressure [bar] Gas consumption: volume of gas consumed at normal pressure (0.5MPa) 棱边去除毛刺，未注棱边、孔口倒角C0.2； E-E 零件号 注意气路孔道联通； 注意螺孔深度，不要打穿气路孔道； 替代 共...