Corrosion Resistant Quality Products. Service Excellence. © Hammond Manufacturing Data Subject to change without notice

Corrosion Resistant Quality Products. Service Excellence. © Hammond Manufacturing Data Subject to change without notice

www.hammondmfg.com 1414 N4 AL Aluminum Series - NEMA 4 Lift-Off Cover Corrosion Resistant Junction Boxes • Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures. • Provides protection where equipment may be hosed down or otherwise be very wet, or in specic applications where corrosion is a problem. • Formed from 0.08" Type 5052 H-32 aluminum. • Sizes smaller than 6" x 6" are formed from 0.06" aluminum. • Smooth, continuously welded seams without knockouts, cutouts or holes. • Welded brackets provide...

1414 N4 AL Aluminum Series - NEMA 4 Lift-Off Cover Front View SEE MOUNTING FOOT DETAIL Side View Bottom View STUD LOCATION GROUND STUD C Ground stud location for 1414N4ALA Mounting Detail When B= 4 Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless specified otherwise ) Hammond Manufacturing Quality Products. Service Excellence. Data Subject to change without notice

www.hammondmfg.com 1590Z Diecast Aluminum Enclosures - NEMA 4X Watertight, Thick Wall Corrosion Resistant • Designed for use as electronic instrument enclosures, electrical junction boxes or terminal wiring enclosures. • Rugged diecast aluminum alloy BS1490, LM6. • Two piece "tongue & groove" construction with a silicone rubber provides protection against dust accumulation and water. • Ideal for repetitive opening and closing. • Four recessed stainless steel machine screws secure lid into tapped holes. Screws are self captivating using either individual neoprene "O" rings (outside the lid gasket...

www.hammondmfg.com 1590Z Diecast Aluminum Enclosures - NEMA 4X Watertight, Thick Wall Junction Boxes Units inch Corrosion Resistant Inches are for reference only. Use metric for precise measurements. Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless specied otherwise Quality Products. Service Excellence. © Hammond Manufacturing Data Subject to change without notice

www.hammondmfg.com R100 Diecast Aluminum Enclosures - NEMA 4X Corrosion Resistant Standards • CSA-US Type 4 • Complies with • NEMA 4 • IEC 60529, IP66 Junction Boxes • Aluminum diecast G AI SI 12 / DIN 1725, Leg 230 • Captive stainless steel lid screws are standard. • Neoprene oil and petrol resistant gasket standard. • Temperature range -30°C to +100°C (-22°F to +212°F). • Single-channel Fastening System. Trouble-free turning 90° to 90° with square enclosures by synchronous arrangement of channels. Finish • Textured polyester powder coat, beige RAL 7032. Technical references and CAD downloads...

www.hammondmfg.com R100 Diecast Aluminum Enclosures - NEMA 4X Part No. inch inch Junction Boxes Width Length Height A B C 2.56 1.97 1.57 Corrosion Resistant Inches are for reference only. Use metric for precise measurements. Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless specied otherwise Quality Products. Service Excellence. © Hammond Manufacturing Data Subject to change without notice

www.hammondmfg.com 1418 Series Single Door Aluminum Enclosures - NEMA 4 Continuous Hinge, Clamped Cover Corrosion Resistant Wallmount Enclosures • Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures. • Provides protection where equipment may be hosed down or otherwise be very wet, or in specic applications where corrosion may be a problem. • Formed from 0.10" Type 5052 H-32 aluminum. • Smooth, continuously welded seams without knockouts, cutouts or holes. • Door and body stiffeners are provided in...

1418 Series Single Door Aluminum Enclosures - NEMA 4 Continuous Hinge, Clamped Cover Front View MOUNTING FEET Panel Size O Vertical stiffener required on KK and M only. © Omit center body stiffener if A is less than 41". © Padlocking hasp and staple. O Omit 2 middle studs if A is less than 31". Omit body stiffeners if A or B is less than 29 . © Omit 2 middle studs if B is less than 31". O Omit door stiffener if A or B is less than 31". Flat panel Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless specified otherwise Quality Products. Service...

www.hammondmfg.com Eclipse Junior Series Stainless Steel Enclosures - NEMA 4X Single Door Enclosures Corrosion Resistant Junction Boxes • Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures. • Provides protection where equipment may be hosed down or otherwise be very wet, or in specic applications where corrosion may be a problem. • For high temperature applications, a gasket retainer may be required, please refer to factory. • Body and cover are formed from 16 gauge 304 or 316 stainless steel •...

www.hammondmfg.com Eclipse Junior Series Stainless Steel Enclosures - NEMA 4X Single Door Enclosures Corrosion Resistant Junction Boxes Technical references and CAD downloads available at www.hammondmfg.com All dimensions in inches unless specied otherwise Quality Products. Service Excellence. © Hammond Manufacturing Data Subject to change without notice

www.hammondmfg.com 1414 N4 PHSS Series Stainless Steel Enclosures - NEMA 4X Continuous Hinge, Clamped Cover Corrosion Resistant Junction Boxes • Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal wiring enclosures. • Provides protection where equipment may be hosed down or otherwise be very wet, or in specic applications where corrosion may be a problem. • Formed from 14 gauge 304 or 316 stainless steel. • Smooth, continuously welded seams. • Welded brackets provide for enclosure mounting. • Continuous stainless...