*mydirectindustry

Catalogs
Hamilton Process Analytics
Incyte Arc Expert - 120

Incyte Arc Expert - 120

Product catalog summary

Product Overview: The Incyte Arc Expert sensors are designed for real-time, in-situ measurement of viable cell density, allowing for immediate detection and response to events without increased off-line sampling.

Specifications:

Sensor Family: Incyte Arc Expert
Length: 120 mm
Parameter Measured: Viable Cell Density
Electrical Connector: VP8
Sensor Output: Arc: Modbus
Measurement Principle: Permittivity
Measuring Range: 0 to 700 pF/cm, equivalent to 5 x 10⁵ to 8 x 10⁹ cells/mL (mammalian)
Accuracy at 25°C: Conductivity (at 0 pF): ± 25 µS or ± 1%, whichever is greater
Precision at 25°C: Permittivity (at 1 MHz): ± 1 pF or ± 1%, whichever is greater
Temperature Sensor: Yes
Configurable Values: VCD, Conductivity, Temperature
Diameter: 12 mm
Process Connection: PG13,5
Wetted Parts: Platinum, Stainless Steel 1.4435, PEEK, EPDM
O-ring Material: EPDM
Surface Quality of Steel: Ra < 0.4 µm (N5)
Digital Interface: RS485 Modbus (max. 31 addresses)
Baud Rate: 19200, 38400, 57600, 115200 Bd
Operating Voltage: 24 V (± 10%)
Serial Number: Yes
Certificate: Yes
Autoclavable: Yes, max. Temperature 130°C (Revision 00), 140°C (Revision 01 and higher)
CIP: Yes
Steam Sterilizable: Yes, max. Temperature 140°C
Operating Temperature Range: 0 to 60°C
Conductivity Range: 1 to 80 mS/cm (firmware below CDCUM003), 0.5 to 80 mS/cm (firmware CDCUM003 and above with Hamilton calibration)
Pressure Range: 0 to 12 bar
Resolution at 25°C: 0.1 pF/cm
Max. Accuracy: Conductivity (at 0 pF): ± 100 µS (for whole operating temperature range)
Max. Precision: Permittivity (over all frequencies): ± 1 pF (for whole operating temperature range)

Additional Information: Specifications are subject to change without notice. For more details, visit the Hamilton Company website.

Catalog excerpts

Incyte Arc Expert - 120 Specification Sheet (Part/REF # 243950-0211) Incyte Arc sensors enable real-time, in-situ measurement of viable cells, making it possible to detect events and respond in real time without increased off-line sampling. Product Specifications Sensor Family Viable Cell Density Electrical Connector Sensor Output Measurement Principle Measuring Range 0 to 700 pF/cm, equivalent to 5 x 10^5 to 8 x 10^9 cells/mL (mammalian) Conductivity (at 0 pF): ± 25 µS or ± 1 % Whichever value is greater over the entire measuring range Permittivity (at 1 MHz): ± 1 pF or ± 1 % Whichever value is greater over the entire measuring range Temperature Sensor Configurable Values Process Connection Wetted Parts Platinum Stainless Steel 1.4435 PEEK (Polyetheretherketone) EPDM (Ethylene propylene elastomer) O-ring Material EPDM (Ethylene propylene elastomer) Surface Quality of Steel Digital Interface Baud Rate Operating Voltage Serial Number Yes, max. Temperature 130 °C (Incyte Arc Revision 00) Yes, max. Temperature 140 °C (Incyte Arc Revision 01 and higher) Steam Sterilizable Operating Temperature Range Conductivity Range 1 to 80 mS/cm for firmware below CDCUM003 0.5 to 80 mS/cm for firmware CDCUM003 and above (with Hamilton ca

Open the catalog to page 1

Conductivity (at 0 pF): ± 100 µS (for whole operating temperature range) Permittivity (over all frequencies): ± 1 pF (for whole operating temperature range) Specifications are subject to change without notice https://www.hamiltoncompany.com/sensors/243950-0211 Spec. Version

Open the catalog to page 2

All Hamilton Process Analytics catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list