*mydirectindustry

Catalogs
Hamilton Process Analytics
Conducell 4UHF Arc 120

Conducell 4UHF Arc 120

Product catalog summary

Product Overview: The Conducell 4UxF Arc conductivity sensors are designed for storing calibrations within the sensor and direct connection to control systems. They are part of the Conducell 4UxF sensor family and measure conductivity using a 4-pole contacting principle.

Specifications:

Parameter: Conductivity (4-Pole)
Sensor Output: Arc: Modbus, 4 to 20 mA
Length: 120 mm
Electrical Connector: VP8
Measuring Range: 1 µS/cm to 300 mS/cm
Accuracy at 25 °C: ± 3% at 1 µS/cm to 100 mS/cm, ± 5% at 100 to 300 mS/cm
Cell Constant: 0.36/cm
Temperature Sensor: NTC 22 kOhm
Configurable Values: Conductivity: µS/cm, mS/cm; Temperature: °C, °F, K
Diameter: 12 mm
Process Connection: PG13,5
Wetted Parts: Stainless Steel 2.4602, PEEK, EPDM
Surface Quality of Steel: Ra < 0.4 µm (N5, electropolished)

Interfaces:

Analog Interface 1: 4 to 20 mA for conductivity, programmable
Analog Interface 2: 4 to 20 mA for Temperature, programmable
Galvanic Isolation: Not isolated; pulse width modulation 3.5 kHz
Digital Interface: RS485 Modbus (max. 31 addresses)
Baud Rate: 4800, 9600, 19200, 38400, 57600, 115200 Bd

Operating Conditions:

Operating Voltage: 7 to 30 VDC max. 150 mW
Operating Temperature Range: Analog interface: 0 to 110 °C; Digital interface: 0 to 140 °C
Pressure Range: 0 to 20 bar (130 °C)

Certifications and Approvals:

Serial Number: Yes
Certificate: Yes, with calibrated cell constant
ATEX Approval: No
IECEx Approval: No
Autoclavable: Yes, max. Temperature 130 °C
CIP: Yes
Steam Sterilizable: Yes, max. Temperature 140 °C

Additional Information: Specifications are subject to change without notice. For more details, refer to the Material Specification document.

Catalog excerpts

Conducell 4UHF Arc 120 Specification Sheet (Part/REF # 243590-3111) Conducell 4UxF Arc conductivity sensors allow calibrations to be stored in the sensor and direct connection to the control system. Product Specifications Sensor Family Sensor Output Electrical Connector Measurement Principle Measuring Range ± 3 % at 1 µS/cm to 100 mS/cm, ± 5 % at 100 to 300 mS/cm Cell Constant Temperature Sensor Configurable Values Conductivity: µS/cm, mS/cm; Temperature: °C, °F, K Process Connection Wetted Parts Stainless Steel 2.4602 PEEK (Polyetheretherketone) EPDM (Ethylene propylene elastomer) See compliance details in Material Specification document Surface Quality of Steel Galvanically not isolated; pulse width modulation 3.5 kHz Digital Interface Baud Rate Operating Voltage Serial Number Yes, with calibrated cell constant ATEX Approval IECEx Approval Steam Sterilizable

Open the catalog to page 1

Operating Temperature Range Analog interface: 0 to 110 °C; Digital interface: 0 to 140 °C Specifications are subject to change without notice https://www.hamiltoncompany.com/sensors/243590-3111

Open the catalog to page 2

Conducell 4UHF Arc 120

Conducell 4UHF Arc 120

Catalog excerpts

All Hamilton Process Analytics catalogs and technical brochures