Catalogs >
HAMAMATSU >
PHOTOSENSOR AMPLIFIER

PHOTOSENSOR AMPLIFIER
1 / 7Pages

Catalog excerpts

Digital output function, current-to-voltage conversion amplifier for amplifying very slight photocurrent with low noise The C9329-01 is a current-to-voltage conversion amplifier used to amplify very slight photocurrent from a photodiode with very low noise. Three ranges of photocurrent detection sensitivity level (H, M, L) are selectable to match the input signal. The C9329-01 operates on the built-in dry batteries so it can be easily used anywhere. The C9329-01 can be directly connected to a personal computer through the RS-232C interface allowing you to acquire high-resolution (16-bit) digital output signals and use the data logger function. T hree sensitivity ranges H : 1 × 109 (V/A) M: 1 × 107 (V/A) L : 1 × 105 (V/A) Precision photometry Laser monitors Optical power meters Selectable operation modes (analog output/digital output) Low signal current preamplifiers Serial connection (RS-232C) with PC Data logger function, low battery function Operates on either dry battery or stabilized DC power supply Absolute maximum ratings (Ta=25 °C unless otherwise noted) Parameter Supply voltage Supply current Operating temperature*1 Storage temperature*1 Symbol Vs max Iin max Topr Tstg When there is a temperature difference between a product and the surrounding area in high humidity environments, dew condensation may occur on the product surface. Dew condensation on the product may cause deterioration in characteristics and reliability. *2: When used with a dry battery, temperature will be +5 to +40 °C. Note: xceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product E within the absolute maximum ratings.

Open the catalog to page 1

Photosensor amplifier Electrical and optical characteristics (Ta=25 °C) Parameter Conversion impedance Input photocurrent Ip Lower Upper Lower Upper Lower Upper L Output offset voltage drift Output offset voltage temperature drift Maximum output amplitude voltage Analog Output noise voltage output (Manual Output resistance mode) Input capacitance Capacitive load Digital output (Remote mode) Interface A/D conversion voltage range A/D conversion cycle mV/day µV/°C 50 ms *5 Supply voltage Vs +6 +12 +13 V Typical connection to photodiode *6 Current consumption Is 20 mA Battery lifetime RL > 10...

Open the catalog to page 2

Photosensor amplifier Connection example Operation example by digital output (Remote mode) BNC cable E2573 Cable with DC plug* (need not be connected when operating on battery) Switch C9329-01 rear SW to "Remote mode" Stabilized DC power supply * Accessory KACCC1184EA Note: se the Rf range switch to change the detection sensitivity. U (Detection sensitivity cannot be changed from the PC.) Display example of accessory sample software Data logger setting range Measurement interval: 50 ms to 1 min (50 ms interval) Measurement count: 32000 max. Measurement interval × Meassurement count: 20...

Open the catalog to page 3

mensional outline (C9329, unit: mm) Photosensor amplifier Dimensional outline (unit: mm) 90 ± 1 Front Rf RANGE AUTO ZERO PUSH START Rear MANUAL MODE REMOTE MODE Upper surface ONLY FOR REMOTE MODES ∙ Sample software CD-ROM ∙ Cable with DC plug ∙ Dry battery (built into the unit) KACCA0137EA A photodiode, coaxial cable with BNC-BNC plug and RS-232C cable are not supplied with the C9329-01. You will need an RS-232C cable (straight cable terminated with a D-sub 9-pin female connector at both ends) available from electronics supply houses. Options (sold separately, unit: mm) ∙ BNC cable E2573

Open the catalog to page 4

Photosensor amplifier Si photodiodes with BNC connector S2281 series The S2281 series photodiodes are sealed in a metal package with Photosensitive a BNC connector and designed to connect to The C9329-01 photosensor amplifier. Two different spectral response ranges are provided. The large photosensitive area makes the S2281 series suitable for optical power meters. A variant type the S9219 with a visual compensation filter is also available.Hamamatsu also provides the E2573 BNC cable (length: 1 m) as an option. Structure Parameter Photosensitive area size Photosensitive area Package Window...

Open the catalog to page 5

Photosensor amplifier Dimensional outline (S2281 series, unit: mm) 190 400 600 Dimensional outline (unit: mm) S2281, S2281-01 BNC : UG-625B/U Core : Cathode Case: Anode

Open the catalog to page 6

Photosensor amplifier Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions ∙ Disclaimer Technical note ∙ Photosensor amplifiers, Photodiode modules Information described in this material is current as of January 2023. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to...

Open the catalog to page 7