Catalogs >
HAMAMATSU >
MPPC® modules C14452 series

MPPC® modules C14452 series
5Pages

Catalog excerpts

MPPC® modules C14452 series Optical measurement modules for low-level light detection, analog output The C14452 series are optical measurement modules capable of detecting low-level light using its built-in MPPC for the visible to near infrared region. These modules consist of an MPPC, an ampliﬁer, a high-voltage power supply circuit, and a temperature compensation circuit. The photosensitive area is available in two sizes of ϕ1.5 mm and ϕ3 mm, and the signal output is analog. The modules operate just by connecting them to an external power supply (±5 V). For the visible to near infrared region Flow cytometry Low noise equivalent power Low-level light measurement Built-in temperature compensation circuit Fluorescence measurement Analytical instrument Analog output Structure Parameter Eﬀective photosensitive area Pixel pitch Number of pixels Absolute maximum ratings Parameter Supply voltage Operating temperature Storage temperature Symbol Vs Topr Tstg *1: When there is a temperature diﬀerence between a product and the surrounding area in high humidity environment, dew condensation may occur on the product surface. Dew condensation on the product may cause deterioration in characteristics and reliability. Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. Electrical and optical characteristics (Ta=25 °C, λ=λp, Vs=±5 V, unless otherwise noted) Parameter Spectral response range Peak sensitivity wavelength Temperature stability of output voltage Photoelectric conversion sensitivity High band Cutoﬀ frequency Low band Rise time Noise equivalent power Minimum detection limit Maximum output voltage Ta=25 ± 10 °C -3 dB, sine wave 10% to 90%, 1p.e. Dark state Dark state

Open the catalog to page 1

MPPC modules Electrical characteristics Parameter Supply voltage*2 Current consumption *2: A power supply with 300 mA or higher output must be used. Block diagram Amplifier Analog output Temperature sensor Power supply for MPPC C11204-01 ±5 V Connection example Using the supplied power cable, connect the MPPC module to a power supply. You can observe the MPPC module’s output waveform by connecting the module to an oscilloscope. Light source Power cable (accessory) MPPC module Subject Analog signal cable KACCC1001EA

Open the catalog to page 2

MPPC modules Measurement example Analog output (Incident light level: 200 pW, λ=λp) Photoelectric conversion sensitivity vs. wavelength (Typ. Ta=25 °C) Photoelectric conversion sensitivity (V/W) Frequency characteristics (typical example)

Open the catalog to page 3

MPPC modules Pulse condition Repeat rate: 5 kHz Pulse width: 2 μs Duty ratio: 1% Incident light level (W) KACCB0584EA Dimensional outline (unit: mm) 22 Photosensitive surface Photosensitive area 15 Power connector 53047-0310 (Molex) Offset adjustment trimmer Analog output connector (MMCX connector) 1.6 Tolerance unless otherwise noted: ±0.3 KACCA042

Open the catalog to page 4

MPPC modules Accessories ‧ Power cable ‧ Instruction manual Options (sold separately) MMCX-BNC cable A12763 Dimensional outline (unit: mm) +50 0 MPPC module lineup Type no. C14455-1550GA C14455-3050GA C14455-1550GD C14455-3050GD Output format Analog Digital Cooling TE-cooled TE-cooled Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions ‧ Disclaimer MPPC is a registered trademark of Hamamatsu Photonics K.K. Information described in this material is current as of March 2020. Product specifications are subject to change without prior notice due to improvements or other...

Open the catalog to page 5