Image sensor modules C16090 series Built-in InGaAs area image sensor, USB 3.1 Gen 1 interface The C16090 series is an image sensor module with an InGaAs area image sensor. This product consists of a driver circuit, temperature controller, and high-speed communication controller, etc. It outputs analog video signals from an InGaAs area image sensor as digital output. The driver circuit consists of an analog front end, A/D converter, and digital controller. From a PC connected via USB 3.1 Gen 1 interface, various settings can be configured, images can be retrieved, and the temperature of the InGaAs area image sensor can be controlled. Near infrared non-destructive inspection (farm product inspection, semiconductor inspection, etc.) The temperature of the InGaAs area image sensor can be controlled. Hyperspectral imaging C mount lens compatible USB 3.1 Gen 1 interface Selection guide Type no. C16090-01 C16090-02 C16090-03 C16090-04 Spectral response range (μm) 0.95 to 1.69 1.12 to 1.85 1.3 to 2.15 1.7 to 2.55 InGaAs area image sensor (built-in) Number of Pixel size Pixel pitch Image size pixels (ch) (μm) (μm) (mm) Two-stage TE-cooled *1: Factory setup prior to shipping (can be changed with driver software) Structure (Typ. Ta=25 °C, unless otherwise noted) Parameter A/D resolution Interface Internal/external trigger mode Port switching Specification 16 USB 3.1 Gen 1 (data transfer speed: 5 Gbps) Internal trigger mode: runs without external triggers External trigger mode: runs in sync with external triggers. Rising or falling edge selectable. Trigger level: LVTTL (0/3.3 V) 4 ports and 1 port switchable Absolute maximum ratings (Typ. Ta=25 °C unless otherwise noted) Parameter Supply voltage Input signal voltage (external trigger) Operating temperature Storage temperature Symbol Vs Vix Topr Tstg *2: When there is a temperature difference between a product and the surrounding area in high humidity environments, dew condensation may occur on the product surface. Dew condensation on the product may cause deterioration in characteristics and reliability. *3: When setting the sensor cooling temperature to -20 °C, set the operating temperature to 30 °C or less. Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. 1

Image sensor modules Electrical characteristics (Typ. Ta=25 °C, unless otherwise noted) Parameter Operating frequency Frame rate Integration time Noise Dynamic range Conversion gain Condition Integration time=1 μs Integration time=1 μs Input signal voltage (external trigger) Supply voltage Current consumption USB bus power current consumption A/D resolution Number of readout ports Interface Trigger mode Symbol fop FR Nread Drange Gc Vih Vil Vs Ic Ic_USB - Unit MHz frames/s μs ADU μV/ADU V V V A mA bit - Temperature controller (Ta=25 °C unless otherwise noted) Parameter Sensor cooling temperature*4...

Image sensor modules C mount C mount lens can be attached using the C mount holder included with the product. Imaging mode There are two imaging modes: internal trigger mode in which the image sensor module operates by itself and external trigger mode in which the exposure timing can be set using external triggers. Internal trigger mode External trigger mode Positive polarity

Image sensor modules Timing chart (external trigger mode) [Positive polarity] External trigger MSP VIDEO-S [Negative polarity] External trigger MSP VIDEO-S Delay time from when an external trigger is input to when exposure is started=30 ns Jitter=±10 ns Minimum pulse width of external triggers=100 ns KACCC0945EA Connection example A USB 3.1 Gen 1 interface is required on the PC. Connect to the PC using the USB 3.1 cable, and install the driver software in the PC. The digital controller runs on the bus power through the USB 3.1 cable. When the digital controller starts, the power supply input...

Image sensor modules AC adapter Parameter Input voltage, Input frequency Output voltage, Output current Image sensor module to adapter Cabe length Adapter to outlet Dimensions (adapter) Weight Software ∙ Compatible OS: Windows 10 ∙ DCAM-API (digital camera application programming interface): Download from https://dcam-api.com. It includes Hamamatsu driver software, DLL, and image capture software. DCAM-SDK, which includes the function manual and sample software, is available. Note: Image processing library is not provided. Accessories ∙ AC adapter ∙ USB cable Related information www.hamamatsu.com/sp/ssd/doc_en.html...