STAINLESS STEEL HIGH PRESSURE 37° TUBE FITTINGS 1/8’’ TO 2’’

If necessary, see SAE Standard J514 for a complete list of dimensions. NPT Tapered Pipe Threads meet the requirements of ASME/ANSI B.I.20.1. All 37° Flared Tube Fittings 3-Piece Tube Assembly can be used with a metric tube by using a metric 37° sleeve, instead of an inch sleeve. Each dimension table shows which metric sleeve should be used for every size. ASSEMBLY INSTRUCTIONS 1. Cut the tube to the proper length. 2. Slide the nut and sleeve onto the tube. (see Fig.1). 3. With a special flaring tool, form the flare to 37° dimension according to SAE STD. J533. (see Fig.2 page 125). 4. Screw the...

ASSEMBLY INSTRUCTIONS Perform flaring according to SAE J533. See Fig. 2. See Table 1 below for dimensions. Figure 2 TABLE 1: FLARING A Single Flare Diameter Max To ensure satisfactory flare production, tube end deburring might be required prior to flaring. It is usually necessary to break the inside corner smoothly before single flaring. In addition, some non-ferrous tubing is normally required to eliminate the cutoff burr, which might otherwise create leakage paths across a substantial portion of the flare. Smoothly breaking the outside corner prior to single flaring, or both the outside and...

SLEEVE______________________ For 3-piece tube assembly S.A.E. 070115 All 37° Flared Tube Fittings 3-Piece Tube Assembly can be used with a metric tube by using a metric 37° sleeve, instead of an inch sleeve. Each dimension table shows which metric sleeve should be used for every size. FEMALE CONNECTOR ____

SLEEVE FOR 3-PIECE TUBE ASSEMBLY INCH SLEEVE Ordering Information METRIC SLEEVE Tube O.D. Ordering Information Metric sleeves are used with standard nuts & bodies. Ordering Information “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice. HAM-LET ADVANCED CONTROL TECHNOLOGY

REDUCING ADAPTER TUBE (INCH) Tube O.D. Ordering Information Ordering Information “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.

Ordering Information Ordering Information “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice. HAM-LET ADVANCED CONTROL TECHNOLOGY

Ordering Information Wrench Flat inch “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.

Ordering Information Wrench Flat inch “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice. HAM-LET ADVANCED CONTROL TECHNOLOGY

FEMALE CONNECTOR Ordering Information “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.

MALE CONNECTOR Ordering Information “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice. HAM-LET ADVANCED CONTROL TECHNOLOGY

MALE CONNECTOR SAE straight thread boss connects flared tube ends to straight thread boss S.A.E. 070120 Ordering Information “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.

MALE ELBOW Wrench Flat inch “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice. HAM-LET ADVANCED CONTROL TECHNOLOGY

FEMALE ELBOW Ordering Information Wrench Flat inch “D” Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice.

"D" Dimension is minimum opening. Dimensions are for reference only, and are subject to change without notice. HAM-LET ADVANCED CONTROL TECHNOLOGY (^HAM-LET

UNION ELBOW Ordering Information Wrench Flat inch “D” Dimension is the minimum opening. Dimensions are for reference only, and are subject to change without

Ordering Information Wrench Flat inch “D” Dimension is the minimum opening. Dimensions are for reference only, and are subject to change without HAM-LET ADVANCED CONTROL TECHNOLOGY

Ordering Information Wrench Flat inch “D” Dimension is the minimum opening. Dimensions are for reference only, and are subject to change without

BULKHEAD UNION Ordering Information “D” Dimension is the minimum opening. Dimensions are for reference only, and are subject to change without HAM-LET ADVANCED CONTROL TECHNOLOGY

Wrench Flat inch “D” Dimension is the minimum opening. Dimensions are for reference only, and are subject to change without

TUBE PLUG Ordering Information “D” Dimension is the minimum opening. Dimensions are for reference only, and are subject to change without HAM-LET ADVANCED CONTROL TECHNOLOGY