TOOLING CATALOGUE
44Pages

V = die-opening B = minimum length ofthe leg for a bending angle a = 90° Ri = internal radius of the bend F = required bending force in tonnage per meter bending length S = plate thickness in mm Remark: this table is only suitable for mild steel with Rm = 450 N/mm2 and E = 210000 N/mm2 and only applicable to air bending!

HACO TOOLING CATALOGUE CONFIGURATIONS Different tool-systems are offered to fulfill the specific needs of the customers. Configuration 1: HACO height modufix manual/hydraulic clamping height equidur tooling remaining opening - ram in top dead centre remaining opening - ram in bottom dead centre height OZU – Single-V die height (anti-deflection-) table for OZU – Single-V die height intermediate part System tooling height punch System tooling height die System tooling height (anti-deflection-) table for System tooling total height punch Haco type height clamping Haco type punch height Haco type...

HACO TOOLING CATALOGUE SYSTEM TOOLING System tooling is available in a wide range of different bottom and top tools, to adapt the machine to almost any specific job. System tooling is manufactured within the smallest tolerances in standard lengths of 835 and 415 mm so they can be put together to achieve larger lengths. System bottom tooling in combination with an anti-deflection table results in a machine with the highest degree of accuracy. System tooling has the following characteristics: Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

HACO TOOLING CATALOGUE SYSTEM TOOLING Tooling composition for pressbrakes with different working lengths. pressbrake - bending length: 1600 mm = (2 x 835 mm) 2000 mm = (2 x 835 mm) + (1 x 415 mm) 2500 mm = (3 x 835 mm) 3000 mm = (4 x 835 mm) 3600 mm = (4 x 835 mm) + (1 x 415 mm) 4000 mm = (5 x 835 mm) 4300 mm = (5 x 835 mm) + (1 x 415 mm) 5000 mm = (6 x 835 mm) 6000 mm = (7 x 835 mm) + (1 x 415 mm) It is possible to equip a pressbrake, machined to take Haco type uppertooling, with System tooling when a special, optional, intermediate clamp is used. The height of this intermediate clamp (see...

When using System tooling there is, in accordance with the current CE regulations, a groove in the length of the bending punch. An adapted securityclamp must be used. When using this securityclamp, it only is possible to clamp CE type tooling. When using a special clamp (non CE) both CE type tooling (with security-groove) and non CE type tooling (no security-groove) can be clamped. Clamps for system tooling. Remark: when ordering the above mentioned intermediate parts, security clamps are not yet included. Remark: the intermediate parts are delivered with anti-deflection wedge. Intermediate...

HACO T OOLING CATALOGUE

HACO T OOLING CATALOGUE

Needs support beam dies (ref. S4006... or S4007...) Needs support beam dies (ref. S4006... or S4007...) Needs support beam dies (ref. S4006... or S4007...)

Needs support beam dies (ref. S4006... or S4007...)

HACO T OOLING CATALOGUE

HACO TOOLING CATALOGUE HACO TOOLING A budget friendly tool system specifically designed for each machine capacity. The multi V-die combines flexibility by having different V-openings into 1 die and easy tool turning. The top bending tool is available in different versions: flexible gooseneck tool 86°, straight tools of 86, 30, 60 or 180°, in full length or sectionalised. Haco tooling has the following characteristics: Tensile strength, Rm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

The dimensions for the clamping of Haco tools depend on the tonnage of the pressbrake. Following dimensions are valid: 175 T < capacity < 260 T 300 T < capacity < 400 T 500 T < capacity < 600 T Tooling for pressbrakes with a capacity over 600 tons are available on request. In addition to the standard tooling shown in this catalogue, tooling can be supplied to suit the customers specific requirements, details are available on request. reference constituing lengths total length PCUT 40...

HACO TOOLING CATALOGUE SINGLEV DIES FIGURE 29 Single V-dies are available in a large variety of angles and V-openings. The small width/height ratio allows an improved access for the workpiece around the die. Single V-die clamping is using a groove in either a Haco or a System tool table. By using the groove as a self alignment system, the tool change can be reduced to very little time. Single V-dies have the following characteristics: - Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

HACO TOOLING CATALOGUE NEW STANDARD TOOLING This system offers a high degree of accuracy, tool changing speed and flexibility. All ‘New Standard’ top and bottom tools are available in a wide range of heights and shapes. They all are manufactured to the smallest possible tolerances resulting in an optimal final bending accuracy. The top tools can be exchanged quickly and safely, vertically as well as horzontally. The self alignment of the dies by using the groove, avoids addittional press strokes, so it is possible to start bending operations immediately after tool-change. New Standard tooling...

HACO TOOLING CATALOGUE NEW STANDARD TOOLING FIGURE 32 New Standard upper-clamping. By means of the New Standard system it is possible to clamp all New Standard BIU-type tools. The New Standard upper-clamping exists in both manual and hydraulic execution. With the manual version, the tooling can be centered and clamped by means of socket set screws. When using the hydraulic system, all tools will be lined up, clamped and centered by one single hit on a button. All units are available in accordance with the bending length and tonnage of the machine. Prices and extensive information is...

HACO T OOLING CATALOGUE HACO T OOLING CATALOGUE

HACO TOOLING CATALOGUE ADJUSTABLE DIES - When using the adjustable die type RS, it is possible to change the V-opening of the die in accordance with the sheet thickness to be bent, thus reducing time-consuming setup-requirements to an absolute minimum. The adjustable die type RS, is supplied with: - a bottom plate with support blocks; - filler blocks. - bending shoulders. - In order to obtain the required V-opening, filler gauges need to be placed between the bending shoulders and the support blocks. The filler blocks need to be added/removed manually. The bending shoulders are hardened so...