Process Controllers P1611100

Product catalog summary

Overview: The Model P161100 Controller is designed to accept either a 0 to 10 VDC or 0/4 to 20 mA DC input signal, providing precise output control to maintain a process at a set value. It features dual 4-digit displays for simultaneous viewing of process value and set-point, with front panel indicators for control and output status. The controller supports PID programming or On/Off control, catering to various application needs.

Specifications:

Input: 0 to 10 VDC or 0/4 to 20 mA DC with specific accuracy and impedance levels.
Display: Two-line, 4-digit LCD with backlighting; red for process display and green for parameter display.
Power: 85 to 250 VAC, 50/60Hz, 8 VA.
Control and Alarm Outputs: Includes relay and logic/SSR outputs with programmable features.
Safety and Compliance: UL recognized, meets IEC and IP65 standards for safety and environmental conditions.

Control Features:

Main Control: PID or On/Off with programmable cycle time and auto-tune capabilities.
Alarms: Two relay alarm outputs with various modes and programmable settings.
Cooling Control: PID or On/Off with programmable cycle time and proportional gain adjustment.

Environmental and Physical Conditions:

Operating Temperature: 0 to 50°C; Storage Temperature: -40 to 80°C.
Humidity: Up to 85% relative humidity (non-condensing).
Vibration and Shock: Compliant with IEC standards for operational conditions.
Construction: Black plastic alloy case with NEMA 4X/IP65 rating for indoor use.

Installation and Safety: The controller is designed for easy installation with wire-clamping screw terminals and meets various safety and electromagnetic compatibility standards.

Catalog excerpts

Process Controller P1611100 0 to 10 VDC or 0/4 to 20mA Input Specification Display The Model P161100 Controller accepts either a 0 to 10 VDC or 0/4 to 20 mA DC input signal and provides accurate output control to maintain a process at a set value. Dual 4-digit displays allow viewing of the process value and set-point simultaneously. Front panel indicators show the control and output status. The PID programming or On/Off control allows these controllers to meet a wide variety of application requirements. Input input Range 2 Line by 4-digit, LCD negative image transmissive with backlighting Top (Process) Display 7.6 mm high digits with red backlighting Bottom (Parameter) Display 5.1 mm high digits with green backlighting Annunciators Status Annunciators: O1 Main control output is active. O2 Cooling output is active (when Alarm 2 is used for cooling) A1 Alarm 1 output is active A2 Alarm 2 output is active °F, °C Temperature units %PW Output power percentage is shown in Bottom display MAN Controller is in Manual Mode R Ramping Setpoint indicator % Percent indicator Display Messages: OLOL Measurement exceeds + sensor range ULUL Measurement exceeds - sensor range SENS Measurement exceeds controller limits dddd Display value exceeds + display range -ddd Display value exceeds - display range Power 85 to 250 VAC, 50/60Hz, 8 VA Control and Alarm Outputs Relay Output Type Form A Contact Rating 3 A @ 250 VAC or 30 VDC; 1/10 HP @ 120 VAC (inductive load) H&B Sensors Ltd | Odyssey House | Durban Road | Bognor Regis | West Sussex | PO22 9RH | United Kingdom Tel: +44(0)1243 866866 | Email: [email protected] | www.hbsensors.com

Open the catalog to page 1

Life Expectancy 100,000 cycles at max. load rating Logic/SSR Output Rating: 45 mA max @ 4 V min., 7 V nominal (main control output only) Main Control PID or On/Off Output Time proportioning or DC Analog Cycle Time Programmable Auto-Tune When selected, sets proportional band, integral time, derivative time, and output dampening time Also sets input filter and (if applicable) cooling gain Probe Break Action Programmable Alarms 2 relay alarm outputs Modes None Absolute High Acting (Balanced or Unbalanced Hysteresis) Absolute Low Acting (Balanced or Unbalanced Hysteresis) Deviation High Acting Inside...

Open the catalog to page 2

All H&b Sensors catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list