FIRE - FIGHTING PUMPS & PACKAGES

HORIZONTAL Split-Case Type PDN-PD FM Approved horizontal split-case type centrifugal re pumps are relatively simple to operate and repair. These pumps have a two-part casing divided in a horizontal plane through the shaft center line. They are well suited to re protection service where a water supply is obtainable under a positive head. CHARACTERISTIC PERFORMANCE RANGE

PUMP DIMENSIONS Caisng half lower Casing half upper Casing wear ring Stainless Steel Radial ball bearing Radial roller bearing Bearing housing Mechanical seal Gland packing Stainless Steel

VERTICAL Shaft, Turbine Type VAB Vertical shaft, turbine type centrifugal re pumps have submerged impellers contained in a series-bowl assembly at the bottom of a vertical shaft. The design is similar to pumps used extensively for industrial and municipal service. These pumps are FM Approved for discharging water from lakes, streams, open sumps, drilled wells and other equivalent subsurface sources. Each pump consists of a discharge head, motor stand, column pipe, line shaft, bowl assembly and suction strainer. For electric drive, FM Approved pumps must be used with a vertical, electric motor....

PUMP DIMENSIONS SECTIONAL DRAWINGS Pump Bowl Column Pipe Stainless Steel Column Pipe Stainless Steel Delivey Casing Wear Ring Wear Ring Pump Shaft Stainless Steel Intermediate Shaft Stainless Steel Stainless Steel Ball Bearing Stainless Steel Motor Stool Bearing Housing Bearing Bracket Gland Packing Teon - Carbon Foundation Plate Suction Strainer Screwed Coupling Coupling Half Side Motor Screwed Coupling Coupling Half Side Pump

TYPICAL INSTALLATION OF FIRE-FIGHTING SETS WITH HORIZONTAL PUMPS )* 1_Diesel engine re pump controller 2_Batteries 3_Jockey pump 4_Concentric discharge increaser 5_Enclosed discharge overow cone 6_Eccentric suction reducer 7_Suction pressure gauge 8_Horizontal pump 9_Circulation relief valve 10_Electric motor 11_Check valve 12_OS& Y gate valve 13_Electric motor re pump controller 14_Jockey pump controller 15_Tlow est fmeter 16_Automatic air release valve 17_Main relief valve 18_Discharge pressure gauge 19_Fuel tank 20_Diesel engine 21_Flexible exhaust connector 22_Exhaust mufer HORIZONTAL FIRE...

TECHNICAL SPECIFICATION FOR HORIZONTAL FIRE PUMPS COMPLY TO NFPA 20 AND/OR FACTORY MUTUAL STANDARDS The set supplied by Audoli & Bertola for re- ghting service shall include the Pump, driver, controller and ttings in the following technical specications. The set shall be manufactured according to the standards of the “National Fire Protection Association”, section 20. The materials shall be: Factory Mutual Research Corporation (FM) approved Underwriters Laboratories (UL) (ULC) listed specically for re-ghting service. All the materials supplied shall be installed as recommended in NFPA 20. TEST...

TYPICAL INSTALLATION OF FIRE-FIGHTING SETS WITH VERTICAL 1_Diesel engine re pump controller 2_Batteries 3_Right angle gear 4_Vertical turbine pump 5_Discharge pressure gauge 6_Jockey pump 7_Automatic air release valve 8_Concentric discharge increaser 9_Check valve 10_OS& Y gate valve 11_Electric motor controller 12_Jockey pump controller 13_Test ow meter 14_Main relief valve 15_Open discharge overow cone 16_Fuel tank 17_Diesel engine 18_Flexible exhaust connection 19_Exhaust mufer VERTICAL PUMPS AT 1n0 RPM, F. M. APPROVED RANGE HEAD. PSI FLOW·RATE USGPM VERTICAL PUMPS AT 1n0 RPM, F. M. APPROVED...

TECHNICAL SPECIFICATION FOR VERTICAL FIRE PUMPS COMPLY TO NFPA 20 AND/OR FACTORY MUTUAL STANDARDS The set supplied by Audoli & Bertola for re- ghting service shall include the Pump, driver, controller and ttings in the following technical specications. The set shall be manufactured according to the standards of the “National Fire Protection Association”, section 20. The materials shall be: Factory Mutual Research Corporation (FM) approved Underwriters Laboratories (UL) (ULC) listed specically for re-ghting service. All the materials supplied shall be installed as recommended in NFPA 20. TEST...

FIRE- FIGHTING Pumping Systems With “Audoli&Bertola” Division, Gruppo Aturia operates in the reghting eld as supplier of water re ghting packages fully in compliance with the European Standards (EN 12845 e EN 12259-12) and the American Standards (NFPA 20). Audoli&Bertola technical skill allows to easily operate in building and industrial elds and to meet the hardest specications required by reneries, petrochemical indutries and off-shore. Gruppo Aturia offers a wide range of centrifugal pumps for re ghting application, both in vertical and in horizontal construction. Audoli&Bertola is the only...

VERTICAL PUMPS TYPICAL INSTALLATIONS

Ansaldo Energia Saipem Snamprogetti Edison Danieli Holzhauer Abb Eni Mondadori Techint Silvani Antibioticos Sonatrach Petrofac Saint-Gobain Nuovo Pignone (Generale Electric) Tecnimont Rigel Nuovo Pignone Rosetti Marino Comau Polibrasil Seda Technip Ecis Group Wormald Ltaliana Foster Wheeler Fiat Johnson Controls Siemens Sud Progetti Riccardi Samir Renery Irasco Piping Engineering Constr Progetti Europa & Global Berger Danway Siraga Fisia Italimpianti British Gas Tunisia Shell Murphy A.m.general Contractor Rahmat Dagangan Enka Teknik SOME REFERENCES A highly efcient servicing organizations, a...