LUBRICATION SYSTEMS BY TIMKEN Page 1 © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN © Groeneveld-BEKA 2024 All rights reserved!

Technical data The oil lubrication pump is consecutively called a device. Order key © Groeneveld-BEKA 2024 All rights reser

General safety instructions All persons that are in charge with the assembly, start-up, maintenance and operation of the device must carefully read these instructions. Furthermore this manual must permanently be available at the site of operation! Basic notes for setup, operation and maintenance can be found below. 3.1 Safety instructions Do not only observe the safety instructions within this main point but also have a look at the special safety warnings that are included in other parts of this documentation. Warning of electrical voltage. Safety instructions which in case of non-observance...

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN 3.4 Obligations of the operator / user a • If movable, rotating, hot or cold parts of the device bear risks, the customer must protect these parts against /|\ contact. This protection must not be removed. / * \ • Any leakages of hazardous substances must be drained in a way that no risks for persons or the environment • Keep to all legal provisions. • Hazards due to electricity are to be excluded. • Examination of pipes and hoses regarding safe provision, use, proper assembly and function has to be carried out according to regionally applicable directives....

General hazard warning – residual risk All components are designed according to valid regulations of the construction of technical systems in regards to operational safety and accident prevention. Independently from this the use can lead to hazards for the user or third parties as well as for other technical facilities. Therefore the device may only fulfill its intended use in a technically acceptable and faultless condition. This has to happen in adherence of the according safety regulations and under observance of the operating manual. Inspect the device and its attachment parts regularly and...

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN 6. Transport and storage Use suitable lifting devices for transport. Do not throw the device or impose it to shocks. Secure the device against toppling down or slipping during transport. A Observe all valid safety and accident prevention regulations for the transport. Wear suitable protective equipment if necessary. Keep adequate distance to suspended loads. The transport help or the elevating device must have the adequate carrying capacity. When storing the device pay attention that the storage area is cool and dry in order to avoid corrosion of...

Functional description 9.1 General The drive of the device occurs rotating. The drive shaft puts the centrally positioned pump shaft and the cam disk with a gear into a rotating movement. This carries out the strokes of the delivery pistons. Max. six delivery pistons with opposite lying control pistons are arranged circular, in the pump body. The oil flow or the suction- and pressure stroke is controlled by the pump shaft via the cam disk, the control wheel and the control piston. The advantage of this construction is that the complete cross-section of the control ducts is open during the whole...

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN 10. Maintenance Disconnect the device from voltage before any maintenance or repair. Both, maintenance and repair, may only be carried out at complete standstill and under pressureless condition. Check the surface temperature of the device, as there is the risk of burns due to heat transfer. Wear heat-resistant gloves and safety goggles! Soiled or contaminated surfaces have to be cleaned before maintenance, wear protective equipment to this purpose, if necessary! Protect the device against recommissioning during maintenance/repairs! • Retighten all...

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN with banjo union and banjo bolt with union screw and double conical ring with banjo union and banjo bolt © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN with banjo union and banjo bolt with union screw and double conical ring with banjo union and banjo bolt © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN © Groeneveld-BEKA 2024 All rights reserved!

GROENEVELD-BEKA LUBRICATION SYSTEMS BY TIMKEN Suction connection Coupling Snap ring When the regulation is in pairs (7-12 pressure connections), the reductions from the order key double, as each pressure connection only gets a pressure pulse with every second rotation of the pump shaft or the stroke washer. The arrangement of the pressure connections and the suction connection is done in the order of the numbering. If another arrangement should be desired, please indicate it when the order is placed. © Groeneveld-BEKA 2024 All rights reserved!

Groeneveld-BEKA GmbH Beethovenstraße 14 91257 PEGNITZ / Bayern Germany Tel. FAX POSTFACH 1320 91253 PEGNITZ / Bayern Germany WEB: E-Mail: www.groeneveld-beka.com [email protected] Gear pumps Multi-line oil pumps Multi-line grease pumps Single-line central lubrication systems Dual line central lubrication systems Oil circulation central lubrication systems Oil-air and spray lubrication Wheel flange central lubrication systems Rolling mill central lubrication systems Utility vehicle central lubrication systems Progressive distributors Control and monitoring devices This document is intended...