Compressed Gas Filters
8Pages

CONSLER7 FILTRATION PRODUCTS CONSLER CP SERIES COMPRESSED GAS FILTERS • ASME Code designed and constructed • Low pressure drop–low energy loss • High flow rate capability • Maximum filter area and dirt holding capacity • Cleanable, reusable filter element • In line connections • Modified and custom designs available • Design Pressures from 180 psi to 740 psi • Contact Factory for higher pressure applications Applications: removal of dust, dirt, pipescale, and other solid contaminants from compressed air and gas pipelines. Effective filtering of high pressure process gas streams to remove product or byproduct solids. Filtering of solid particles ranging from 0.3 to 750 microns. Positive protection of pneumatic controls, meters, and other pipeline equipment. Low pressure applications where pressure loss is critical. Filter efficiencies to 99.97 %. Element Design & Construction The CP Series filter offers a replaceable, cleanable element that incorporates a pleated or "radial fin" cartridge design. The element offers maximum filter area in a compact filter assembly, and provides positive gasket sealing to prevent by-pass of unfiltered gasses. Long filter life, low pressure drop, large dirt holding capacity and efficient filtration are assured. Most models employ only one filter element to permit quick and simple cartridge change out. Standard models, CP 115 and larger, are furnished with a cleanable, sewn-end constructed element which can be reconditioned before replacement is necessary. Following several field cleanings this unique element style can be returned to the factory for recovery and reconditioning. Series elements are also supplied in many alternate materials offering a particle retention range from 0.3 to 750 microns. Optional filter materials available include nylon, fiberglass, cotton, polypropylene, NOMEX*, rayon, wool, DACRON*, TEFLON*, and wire cloth providing an application range from sub-zero temperatures to 1000° F. Standard elements are furnished with a carbon steel center core and corrosion resistant steel support frame. 304 Stainless Steel and other materials are available. Housing Design and Construction Materials of construction include carbon steel, 304 and 316 Stainless Steel as well as other alloys. Housings are designed and constructed in accordance with ASME Code Section VIII, Division I requirements for unfired pressure vessels 5 1/4" diameter and above and are available with "U" Stamp registration and certification. Inlet/outlet connections are furnished in a horizontal in-line configuration. All models can be quickly serviced without breaking pipe connections. Standard Model Features CP 160 and larger CPH 130 and Larger CPHH 130 and larger Closure Assembly CP 180 thru 200 – hinged closure assembly CP 210 and larger – swing away cover devices CPH 160 and larger – swing away cover devices CPHH 150 and larger – swing away cover devices 1/4" NPT Gauge Connections on Inlet/Outlet Nozzles CP 115 and larger CPH 120 and larger CPHH 120 and larger Element Materials Standard elements are furnished with a polyester filter medium providing nominal efficiency on 10 micron solid particles. CP

CP Series Specifications Model No. 1. All dimensions are approximate. 2. See optional elements, pg. 8. • Standard filters are supplied with a 10 micron polyester filter medium (200° F) and a NEOPRENE* closure gasket (300° F). Contact your Consler representative for other available materials. • Models CP 110 have a maximum design of 150 psig at 100° F. • Models CP 115 thru 240 have 1/4" NPT plugged gauge connections. • Models CP 115 thru 150 have 1/2" drainandvent connections. • Models CP 160 thru 200 have 1" drain and vent connections. • Model CP 160 has two (2) handles for closure removal....

Values are based on actual test results or empirical calculations. To determine proper filter sizing for gases other than air, multiply pressure drop by the correction factor for the appropriate gas from chart on back cover. For temperatures freater than 60° F, multiply pressure drop by the absolute temperature factor: 460 + (° F)

1. All dimensions are approximate. 2. See optional elements, pg. 8. Standard filters are supplied with 10 micron polyester filter medium (200° F). Contact your Consler representative for other available materials. Models CPH 120 thru 200 have 1/4" NPT plugged gauge connections. Models CPH 110 thru 150 have 1/2" NPT plugged drain and vent connections. Models CPH 160 thru 200 have 1" NPT plugged drain and vent connections. Models CPH 130 thru 200 have three (3) leg supports with length of 18" from bottom of vessel to grade. • Models CPH 130 thru 150 have two (2) handles for closure removal. •...

CPH Series Flow Capacities1Capacity (SCFM) vs. Differential Pressure (psi) At 60° F-Specific Gravity 1.0 (Air)2 INLET PRESS INLET PRESS 1. Values are based on actual test data or empirical calculations. 3. For inlet pressures less than 200 PSIG, refer to previous flow charts 2. To determine proper filter sizing for gases other than air, multiply pressure drop by the correction factor for the appropriate gas from chart on back cover. For temperatures greater than 60° F, multiply pressure drop by the absolute temperature factor: 460 + (° F) 520 (Continued from page 1) For model CP 120 a...

CPHH Series Specifications Model No. 1. All dimensions are approximate. 2. See optional elements, pg. 8. • Standard filters are supplied with 10 micron polyester filter medium. Contact your Consler representative for other available materials. • Models CPHH 120 thru 200 have 1/4" NPT plugged gauge connections. • Models CPHH 110 thru 150 have 1/2" NPT plugged drain and vent connections. • Models CPHH 160 thru 200 have 1" NPT plugged drain and vent connections. • Models CPHH 130 thru 190 have three (3) leg supports with length of 18" from bottom of vessel to grade. • Model CPHH 200 has four...