Catalog excerpts
GOULDS PUMPS Polyshield® Baseplate/Foundation System
Open the catalog to page 1
Polyshield ® Baseplate/Foundation System • 316SS Fastener and Inserts are standard. • One-piece removable Polymer Motor Block. Provides full motor foot support to minimize soft foot conditions. Each block accommodates two NEMA motor sizes. • Self-venting design with Grout Hole and plug. • Integral Drip Basin. • Standard 316SS Inserts provide flatness of 0.005"/ft. (Optional A-20 and Hastelloy C available.) Optional Machine Mounting Pads (shown here) provide flatness of 0.002"/ft. • 316SS Jack Bolts for fast & accurate motor alignment. • CPVC Drain connection standard. • Available in heights...
Open the catalog to page 2
Now compare the advantages! Significantly Less Installation Costs Because of the reduced number of steps, Polyshield® can lower the number of hours needed to complete the installation up to 64% over conventional Cast Iron or Fab Steel bases. $7,492 $5,670 $5,103 Cost in Dollars $ 8000 7000 6000 5000 4000 3000 2000 1000 0 PIP Steel Base PreGrouted Cast Iron $5,078 Polyshield ® Chemical Resistance Method Comparison Typical Procedure Concrete Polyshield Foundation Foundation Install rebar Construct a form Mix concrete Pour concrete Wait for initial cure Break out form Cure for 7-28 days...
Open the catalog to page 3
Installation Steps for Polyshield ® Installation & Maintenance Savings • Baseplate & Foundation Polyshield® Baseplates are less expensive than most metal bases and epoxy grout foundations. • Grout Polyshield® Baseplates are filled with regular 3000psi concrete fill which is less expensive than epoxy grouts. Install Polyshield ® Foundation complete with pump and motor over rebar. • Preparation Metal baseplates must be sandblasted for grout adhesion. Polyshield does not. Note: No need to remove pump and motor. • Installation No concrete forms, no grout air pockets and no long cure times as...
Open the catalog to page 4All Goulds Pumps catalogs and technical brochures
-
IC i-FRAME series11 Pages
-
3420 series11 Pages
-
3316 series12 Pages
-
JC series12 Pages
-
3175 series16 Pages
-
3196 i-FRAME series24 Pages
-
AF series8 Pages
-
318020 Pages
-
370012 Pages
-
Goulds 7200SB12 Pages
-
Vertical Turbine Pumps20 Pages
-
Goulds 340011 Pages
-
Goulds AF8 Pages
-
IC i-FRAME24 Pages
-
Goulds API 3600 i-FRAME®12 Pages
-
Goulds ICP8 Pages
-
Goulds ICO i-FRAME® Series16 Pages
-
Goulds API 3620 i-FRAME®16 Pages
-
Goulds 317516 Pages
-
Goulds API 31718 Pages
-
Goulds 3171 / CV 317116 Pages
-
Goulds 33557 Pages
-
Goulds 33354 Pages
-
Goulds 331612 Pages
-
Goulds 329820 Pages
-
Goulds 318020 Pages
-
Goulds JC Slurry Pump10 Pages
-
Goulds JCU8 Pages
-
Goulds HS / HSD4 Pages
-
Goulds ICB Close-Coupled19 Pages
-
Goulds 3196 i-FRAME Process Pump19 Pages
-
7200CB Barrel Multistage Pumps12 Pages
-
Goulds 36408 Pages
-
Pump Selection Guide16 Pages
-
Goulds Model JC Slurry Pump10 Pages
-
Vertical Cantilever Pump VHS9 Pages
-
SealPlus Mechanical Seals4 Pages
-
ICM8 Pages
-
Mining & Mineral Processing12 Pages
-
Products for Pulp and Paper4 Pages
-
Pumps for Power Generation8 Pages
-
Wet Pit Column Pumps4 Pages
-
Single Suction Dry Pit Pumps2 Pages
-
Model HS and HSD4 Pages
-
LF 3196 i-FRAME11 Pages
-
CV 3196 i-FRAME11 Pages
-
Goulds 3198 i-FRAME11 Pages
-
Goulds Trash Hog®11 Pages
-
Goulds 379611 Pages
-
HT 3196 i-FRAME14 Pages
-
Goulds 3400 Double Suction Pumps11 Pages
-
Goulds API 31714 Pages
-
3196 i-FRAME19 Pages
Archived catalogs
-
Goulds 3420 Double Suction Pumps11 Pages
-
Goulds Model 390013 Pages
-
Medium Consistency Pump Systems11 Pages
-
Goulds Model 317515 Pages
-
Goulds 391011 Pages
-
Goulds Model 550011 Pages
-
Goulds AF Axial Flow Pumps11 Pages
-
Goulds Molten Sulfur Pumps2 Pages
