OIL PROCESSING EQUIPMENT
1 / 21Pages

Introduction: Modem power transformers are an essential link in long-distance transmission of electricity. This is why servicing of transformers throughout their lifecycle (filling with oil, vacuumizing, purification and regeneration of oil, drying etc) must be performed professionally and to the highest standard. GlobeCore manufactures a wide range of equipment to maintain transformers during their entire service life.

What GlobeCore Offers Insulation (paper and oil) damage, contamination and moisture account for approximately 37% of power transformer failures. The GlobeCore regeneration technologies allow complete restoration of transformer oil to bring its performance to the required quality specifications. Timely regeneration guarantees reliable protection of paper insulation, extends transformer lifetime and saves on new oil purchases. Beside regeneration systems, this catalogue offers a choice of other equipment for power transformer servicing.

GlobeCore Regeneration Units the UVR units are designed for regeneration and purification of oil and fuel, the unique feature of the UVR is its capability to process any mineral oil or fuel. With the GlobeCore UVR regeneration technology, the unit can be set to process any type of oil or fluid. Switching from one type of processed fluid to another does not require changing the design of the unit, the UVR unit purifies and clarifies darkened diesel and furnace fuel, removing sulfur and sulfuric hydrogen compounds, easily clarifies gas condensate, removing tar and contamination, bringing the...

GlobeCore Oil Reactivation Units The unit is designed for reactivation of sorbent (Fuller's earth, bleaching clay), used in regeneration columns of oil reactivation systems. After reactivation, the sorbent can be reused for oil regeneration.

Thermal Vacuum Degassing Units The UVM unit is designed for removal of solved gases, free and solved water and particulate matter from oil, as well as for heating transformer oil before filling power transformers and other electrical systems. The UVM units are used during installation and repairs of power transformers. The UVM is a comprehensive solution for transformer manufacturers and servicing facilities. Degassing mode, m /hour Heating and filtration mode, m3/hour Power supply parameters Length without trailer / with trailer Fully customizable Width without trailer / with trailer...

Thermal and Vacuum Degassing Units The secret of the high efficiency of GlobeCore units are activators which promote near-instant release of gases and evaporation of water from oil. The UVM units are equipped with a special oil heater which prevents oil burning due to low mean surface power and prevents oil overheating after the machine is stopped. Beside being highly reliable, the machines are compact and highly mobile.

GlobeCore has offices in the USA, the UAE and the South African Republic. Customer support is offered by 17 dealer representatives around the world. GlobeCore also manufactures equipment for operation on ships and maritime vessels, off-shore drilling rigs and wind farms. GlobeCore has manufactured over 2500 units, now successfully operated the world.

Parameter Value Max oil degassing rate, l/h OIL FILTRATION TRAILER This system includes all transformer servicing components: Oil degassing; 2 Pumping, filtration, heating; 3 Pulling vacuum; Transformer winding dehydration; 5 Low temperature condensation of water from a transformer; Supply of hot air to a transformer. Full automation Nominal output pressure, bar Input oil heater power, kW Nominal vacuum system suction rate, m /hour Power supply

Thermal and Vacuum Degassing Units The CMM units are designed for removal of water and particulate matter from electrical insulation and lubrication oils. The CMM units are used during installation and repairs of power transformers and for washing and filling of hydraulic systems. The CMM units feature simple design, making them easy to operate and service. Beside being highly reliable, the units are compact and highly mobile.

Sorbent cartridges are used to dry oil with zeolite. The sorbent cartridge unit is equipped with hatches for rapid loading and unloading of the sorbent. The unit can be filled not only with zeolite, but also with other sorbents, such as Fuller's earth or silica gel. This allows the unit to be used for reduction of oil acidity and oil regeneration.

BRZ Zeolite Regeneration Unit The BRZ zeolite regeneration units restore performance of zeolite in sorbent cartridges, such as ZP-260. With a stream of hot air, moisture is removed from the sorbent, restoring its absorption properties. BRPS is a modified version of the BRZ with a steam generator. The steam purges the sorbent and removes dust from zeolite. The unit is designed for the power industry and any facility which uses zeolite to dry electrical insulation or lubrication oil.

CFU Oil Filtration Units The CFU units are designed for filtration of lubrication and electrical insulation oils. The units are used for filling and cleaning of gearboxes, hydraulic systems, transformers and in other areas where filtration is required. These units are equipped with universal filter casings. Required filtration fineness can be specified by the customer.

UVD Vacuum Oil Filling UnitThe UVD vacuum oil filling unit is designed for preparation (degassing), storage, transportation and adding transformer oil into high voltage inputs of transformers and switches. Parameter

PPM Continuous Oil Heaters The PPM continuous oil heater is designed for heating of transformer oil during filling or change of the oil and drying of transformers, the unit can heat mineral, industrial, turbine and other oil types, the unit can be used in transformer manufacturing and servicing facilities, power plants and oil processing facilities.

BV Transformer Vacuumizing Units This GlobeCore vacuum unit is designed for pulling vacuum on transformers and other electrical systems. The BV vacuum unit is a double stage vacuum system. The first stage creates preliminary vacuum up to 0.5 mbar. It is equipped with a rotary vane vacuum pump. The second stage brings vacuum to 0.01 mbar. This stage is equipped with a Roots vacuum blower.