THESI 320 POSITION CONTROLLER

1 / 2 PagesView full catalog

THESI 320 POSITION CONTROLLER

Product catalog summary

THESI 320 Position Controller Overview

The THESI 320 is designed to control the shifting and positioning of two axes with three operating modes: Manual, Semi-Automatic, and Automatic.
It features independent axes configurations, 3 auxiliary inputs, and can store up to 99 programs with 20 positions each.
Power supply options include 90-230 Vac or 24 Vac, and it is built with a 16-bit microcontroller.
Inputs and outputs are optoisolated, with voltage-free contact outputs and analog outputs.

Mechanical and Electrical Characteristics

Display: 6 high-efficiency digits for position and 2+2 digits for cycles/programs.
Encoder power supply options: 5 Vdc or 12 Vdc.
Input frequency: 20 kHz max, with linear resolution ranging from 200 µm to 1 µm.
Power consumption: 10 W max, with specific current consumption limits for different power supplies.
Protection class: IP 65 for the keyboard and IP 40 for the rear panel.
Operating temperature range: 0 °C to 50 °C; storage temperature range: -20 °C to 70 °C.

Ordering Code

Model: THESI 320 DI 05V, where DI indicates digital relay outputs and 05V indicates a 5 V encoder power supply.

Installation and Safety Instructions

Installation must be performed by specialized personnel, adhering to manufacturer instructions.
Use a mains power supply with an input filter and fuses, and ensure compliance with safety regulations.
Avoid using the instrument in environments with flammable gases or explosives.
Ensure all connected equipment meets insulation standards.
Cleaning should be done with a moist cloth after disconnecting the power supply.

Catalog excerpts

Via Assunta, 57 - 20834 Nova Milanese (MB) - ITALY Tel. +39 0362 366126 Fax +39 0362 366876 www.givimisure.it [email protected] • THESI 320 position controller can control shifting and positioning of two axes in 3 different operating modes: - MANUAL, by keyboard; - SEMI-AUTOMATIC, by keyboard; - AUTOMATIC, on the basis of a memorized program. • End of program output. • Independent axes as for configurations and parameters. • 3 generic auxiliary inputs. • Possibility of storing up to 99 PROGRAMS with 20 positions each. Up to 99 repetitions can be matched to each position (the program cycle is composed by the position and its respective repetitions). • 90 Vac to 230 Vac power supply, or 24 Vac power supply with selector. • Manufactured with 16 bit microcontroller, 256K FLASH and 8K RAM memory, in single-chip mode. • 5 Vdc or 12 Vdc encoder input. • Optoisolated inputs. START, STOP, INCREASE CYCLE, DEVIATION, PRESET. • Voltage-free contact outputs. OK POSITION, ENABLING WITH CONTROL INTERLOCK FEED / BACK, SLOW / FAST. • ± 10 Vdc analog output. FEED / BACK, SLOW / FAST, with linear ramp. • Possibility of installation on bench or built in. MECHANICAL AND ELECTRICAL CHARACTERISTICS * When using the maximum current, the maximum voltage of the relay contacts is precluded. ORDERING CODE_ MODEL OUTPUTS ENCODER POWER SUPPLY COMPANY WITH QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV = ISO 9001:2008 = GIVI MISURE S.R.L. A SOCIO UNICO C.F. e Iscrizione al Reg. Imprese di Monza e Brianza n° 04355540156 - Cap. Soc. € 51.480,00 I.V.

Open the catalog to page 1

Via Assunta, 57 - 20834 Nova Milanese (MB) - ITALY Tel. +39 0362 366126 Fax +39 0362 366876 www.givimisure.it [email protected] TECHNICAL DATASHEET CONNECTIONS LEGEND POWER INPUT FUSE GROUND TERMINAL SWITCH COM FB SLOW/AV FAST FEED BACK AUX N.O. RELAY CONTACTS 240 VacMAX - 1 AMAX - 120 VAMAX 60 VdcMAX - 2 AMAX - 60 WMAX V+ VA B Z AUX 1 AUX 2 AUX 3 COM+ PRESET START STOP DEV INC.CYCLE EN. MOV. M-S/A OK POS. END PROG COM FS / A0 = AC voltage power supply (220 Vac, 110 Vac, 24 Vac) = External fuses = Protection ground = AC voltage power supply selector 110/220 Vac or 24 Vac = Encoder power supply...

Open the catalog to page 2

All GIVI MISURE catalogs and technical brochures

Archived catalogs

MTT-MTB
2 Pages
VI900
2 Pages
GVS 204
6 Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list