֕ Very sensitive response characteristic Function is not impaired by high back pressureՕ Automatic air-venting (trap can be used for thermal air-venting in steam systems) Installation in any position (horizontal and vertical lines)Օ High hot-water capacities even with low differential pressures With tandem seat (double sealing) for low condensate flowratesՕ Built-in non-return valve Stainless steel internals (corrugated membrane of Hastelloy)Օ Design UӔ with undercooling capsule: utilization of a certain amount of sensible heat by banking-up of condensate, decreasing the amount of flash steam Optional extra: Integrated condensate monitoring for MK 45 (temperature or steam loss) L MK 45-1 DN 15, 20, 25 TypeDesign/ApplicationMK 45-1MK 35/31 > 1 )With tandem seat (double sealing) For low condensate flowrates, steam-tracing, steam-line drainage, air-venting MK 45-2MK 35/32 > 1 )With single seat For medium condensate flowrates, steam-tracing, drainage of heat exchangers, air-venting MK 25/2 > 1 ) MK 25/2 S > 1 1 ) MK 35/2 S ) MK 35/2 S3 For large condensate flowrates, drainage of heat exchangers > 1 )With single seat MK 36/51 > 1 )MK 36/52 > 1 )With tandem seat (double sealing) Ֆ with flat gasket For small/large condensate flowrates, steam tracing, steam-line drainage, venting and vacuum-breaking. Also suitable for food, biological and pharmaceutical applications. > STAINLESS STEEL MK 45 A-1MK 45 A-2 For small and large condensate flowrates; steam-tracing,steam-line drainage, air-venting > L MK 35/31, DN 10, 15 STAINLESS STEEL 1 ) Can also be used for vacuum breaking (aerating). > Steam Trap for Thermostatic Air-Venting with Membrane Regulator The thermostatic steam traps with membrane regulators of the MK series can also be used for air-venting. Application Thermostatic steam trap for automatic air-venting and discharge of non-condensable gases and steam/air mixtures from steam lines and heat exchangers .A special type of membrane might be required. > 1 ) A 182 F316L > 1 ) 29.3 bar / 200аC 24 bar / 400C MK 45 A-2 PN 40 22 1.4404 > 1 ) A 182 F316L > 1 ) 29.3 bar / 200аC 24 bar / 400C > 1 ) Material complies with EN and ASTM requirements. > 2 ) MK 25/2 S DN 40/50: cover made of cast steel GS-C 25 (ASTM nearest equivalent: A 216 Gr. WCB) > 3 ) Physical and chemical properties comply with EN grade. ASTM nearest equivalent grade is stated for guidance only. > L 4 ) EN nearest equivalent grade is stated for guidance only. > * ) For more information see data sheet. >

3 )֖150֖֖Hinged clamp 65 65 6565֖ > MK 25/2 S, DN 40, 50 1 ) MK 45 with ASME flanges: overall length 172 mm available on request. > 2 ) Only MK 45 > 3 ) Made of carbon steel or > L L L stainless steel > MK 36/51, DN 8, 10, 15, 20 mm Connection: screwed socketMK 36/51, DN 8, 10, 15, 20 mm Connection: hinged clampMK 36/51, DN 15 mm Design with union butt-weld nipples The charts show the maximum hot condensate capacities. MK 45-1 (Curve 1) MK 35/31 (Curve 1) MK 25/2 S, DN 40, 50 (Curve 1) MK 35/2 S3, DN 25 (Curve 3) MK 45-2 (Curve 2) MK 35/32 (Curve 2) MK 25/2, DN 40, 50 (Curve 2) MK 35/2S, DN 25...